Member of the Month

je_t.aime_canard
January, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Sketchy mounting questions

profile picture
Coochieman7
Posts: 275 - Karma: 1,395
I have a pair of vacations with 3 mounts in them, the markers I had in them pissed the bed so I want to switch them out for some pivots I have and I would need to remount. Would helio coils or binding freedom screws with extra epoxy hold if my new mounting holes were touching previous mounting holes, and if so does anybody know any homies with a jig in slc who’d be willing to mount them up?
p.s. I don’t care if a ski with more than 3 mounts hurts the durability of the skis, it wouldn’t be the end of the world if these skis snapped
Oct 9 2024 4:02PM
4 0
profile picture
corona
Posts: 12818 - Karma: 32,993
I would 100% avoid having a new hole right next to an old hole. If there was no other place to put the bindings then if you filled in the old holes with epoxy then drilled once it's cured it would probably work, but I think your chance of a ripout is likely still way higher. Can you just mount further forward or back?
Oct 9 2024 4:19PM
5 0
profile picture
Denseclouds
Posts: 528 - Karma: 3,083
I really don't imagine you'd get more than a few days OR a few hard stomps out of drilling into a previous hole before it gives
Oct 9 2024 4:34PM
0 1
profile picture
Non_State_Actor
Posts: 4962 - Karma: 17,827
This thread is useless without pics.
Oct 10 2024 12:24PM
4 2
profile picture
darthlobster603
Posts: 103 - Karma: 944
youre probably going to have to get creative but until you go back more than 3cm youre really not going to notice much of a difference. just make sure you have the proper clearance and the old holes are all plugged and sealed.
Oct 10 2024 12:32PM
0 0
profile picture
iDontHitRails
Posts: 267 - Karma: 2,469
They're J skis, just throw them in the trash where they belong
Oct 10 2024 1:28PM
5 4
profile picture
Poikenz
Posts: 1496 - Karma: 3,888
I believe the general rule is 8mm center to center of old holes to new holes or around 3-4mm between holes to be safe from a tear out.

If all three mounts are yours or you can figure out which bindings/ bsl they were mounted for you would be safer off reusing old holes.
Assuming your old markers are just junk and didn't rip out of your ski, you could always buy a replacement marker binding (either the same one or one that uses the same mounting pattern) and install those in the current holes.

If you really want to do a 4th mount you'll have to do it yourself or find a homie willing to do it as a shop won't touch it for liability reasons.
Oct 10 2024 8:43PM
1 0
profile picture
darthlobster603
Posts: 103 - Karma: 944
just unload them on marketplace for $600 like everyone else and get something else
Oct 11 2024 8:31AM
0 1
profile picture
Coochieman7
Posts: 275 - Karma: 1,395
coronaI would 100% avoid having a new hole right next to an old hole. If there was no other place to put the bindings then if you filled in the old holes with epoxy then drilled once it's cured it would probably work, but I think your chance of a ripout is likely still way higher. Can you just mount further forward or back?


I wouldn’t ever ski them if they were mounted further back because it would have to be -6.
Oct 11 2024 10:13AM
0 0
profile picture
Coochieman7
Posts: 275 - Karma: 1,395
PoikenzI believe the general rule is 8mm center to center of old holes to new holes or around 3-4mm between holes to be safe from a tear out.

If all three mounts are yours or you can figure out which bindings/ bsl they were mounted for you would be safer off reusing old holes.
Assuming your old markers are just junk and didn't rip out of your ski, you could always buy a replacement marker binding (either the same one or one that uses the same mounting pattern) and install those in the current holes.

If you really want to do a 4th mount you'll have to do it yourself or find a homie willing to do it as a shop won't touch it for liability reasons.


The last guy mounted pivots but i know his bsl was longer, i was thinking about maybe using his toe piece mounts and just mounting the heel piece wherever i could get it.

I know a shop wouldn’t do it that why I was asking if anyone had a homie who was willing to do it under the table, I usually mount my own skis but I’m just afraid I’d be slightly off and wouldn’t be close enough for helio coils
Oct 11 2024 11:54AM
0 0
profile picture
skietedavidson
Posts: 95 - Karma: 571
Are you trying to stay with a certain mount? For what it is worth to you, I have tried -4 cm (from center, rec), -1 cm (from center), and know of people who ride them @center. They behave pretty similarly throughout IMO
Oct 11 2024 12:09PM
0 0
profile picture
Coochieman7
Posts: 275 - Karma: 1,395
skietedavidsonAre you trying to stay with a certain mount? For what it is worth to you, I have tried -4 cm (from center, rec), -1 cm (from center), and know of people who ride them @center. They behave pretty similarly throughout IMO


My preferred range would be center to -3
Oct 11 2024 1:01PM
0 0
profile picture
TreeJam
Posts: 356 - Karma: 3,378
Dude just mount them backwards. I have paper jig And will mount ski for you
Oct 11 2024 8:44PM
0 2
profile picture
Sully_Lynn
Posts: 78 - Karma: 197
i got a old shitty pair of honeybadges i have mounted 3 different bindings on and they hold up fine
Oct 13 2024 9:09PM
0 0
profile picture
Coochieman7
Posts: 275 - Karma: 1,395
Sully_Lynni got a old shitty pair of honeybadges i have mounted 3 different bindings on and they hold up fine


How close are the mounting holes?
Oct 14 2024 12:57PM
0 0
profile picture
Sully_Lynn
Posts: 78 - Karma: 197
Coochieman7How close are the mounting holes?


real close
Oct 14 2024 2:59PM
0 0
All times are Eastern (-5)