Member of the Month

Biffbarf
February, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Forward pressure not setup right?

profile picture
lootlake
Posts: 1052 - Karma: 6,832
To make a long story short, I noticed that my attack bindings forward pressure might not be setup up right?

from what I understand the black tabs have to be aligned with the bumps, but in my case it’s too far back

(Boots are clipped in)


if anyone has experience pls let me know this is all my speculation

**This thread was edited on Aug 20th 2024 at 4:04:51pm
7 months ago
3 0
profile picture
PartyBullshiit
Posts: 4515 - Karma: 20,731
https://www.newschoolers.com/videos/watch/1096250/--YouTube
7 months ago
3 1
profile picture
johnblaze
Posts: 1512 - Karma: 2,696
Yeah you need to crank it in a little bit. Not enough forward pressure currently.
6 months ago
4 0
profile picture
lootlake
Posts: 1052 - Karma: 6,832
johnblazeYeah you need to crank it in a little bit. Not enough forward pressure currently.


What I figured haha! Not normal that I release trying a mini nose press lol
6 months ago
2 0
profile picture
Non_State_Actor
Posts: 5018 - Karma: 18,148
vroskiiWhat I figured haha! Not normal that I release trying a mini nose press lol


Yeah, it should just be one click forward from its current position. You want the little lines to be partly in and partly out of the heel piece. There are some good how to videos online for these.
6 months ago
2 0
profile picture
lootlake
Posts: 1052 - Karma: 6,832
Lil update, took them to a tyrolia certified shop to take a look at them, cause I kept double ejecting when trying to butter on grass.. they are not sure whats wrong..





new hypothesis is that I out perform them, I’ve read online that the attack 11 are for more lightweight and low lever skiers.. (I weight 145 and expert skier)

should I upgrade to a higher din binding?
5 months ago
3 0
profile picture
PartyBullshiit
Posts: 4515 - Karma: 20,731
Absolutely
5 months ago
4 0
profile picture
lootlake
Posts: 1052 - Karma: 6,832
Got some pivot 15s for the setup! Can any one confirm if I can remount them at same position(deadcenter) by still using the same boot size ?



found a thread saying I can remount tyrolia holes to pivot without a problem…but it’s a bit outdated just need a second confirmation thanks!
5 months ago
2 0
profile picture
lil.Boye
Posts: 2746 - Karma: 12,541
vroskiiGot some pivot 15s for the setup! Can any one confirm if I can remount them at same position(deadcenter) by still using the same boot size ?



found a thread saying I can remount tyrolia holes to pivot without a problem…but it’s a bit outdated just need a second confirmation thanks!


they don't have the same pattern, might have to shift a bit back to drill new holes
5 months ago
1 0
profile picture
rojo.grande
Posts: 1520 - Karma: 12,381
vroskiiGot some pivot 15s for the setup! Can any one confirm if I can remount them at same position(deadcenter) by still using the same boot size ?



found a thread saying I can remount tyrolia holes to pivot without a problem…but it’s a bit outdated just need a second confirmation thanks!


You should be fine, move them a half cm to be sure the mount patterns don’t match up. Make sure your shop fills and seals the old holes. You’ll be good to go
5 months ago
1 1
All times are Eastern (-5); Currently it's 4:23AM