Member of the Month

hi_vis360
November, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Too much foreward pressure ?

profile picture
D*A
Posts: 37 - Karma: 54
Hi.

I messed up something in a knee landing almost on my back but training to land on my tails.

Was this too much foreward pressure ? This was set up by a shop on the slope. My fault was not checking...

DINS are the same I use since 3 years.

Thanks in advance for the feedback







Mar 28 2024 1:28PM
1 1
profile picture
Berniskier
Posts: 11 - Karma: 61
You need your boot in the binding for a proper forward pressure reading
Mar 28 2024 1:46PM
4 2
profile picture
D*A
Posts: 37 - Karma: 54
It was in the binding!
BerniskierYou need your boot in the binding for a proper forward pressure reading
Mar 28 2024 1:53PM
1 0
profile picture
mjkuby12
Posts: 16 - Karma: 160
After talking to multiple shops about forward pressure on the attacks, my understanding is that as long as your housing falls within the dashes on the tab you are good. It would ideally be perfectly in the middle of the dashes but it does not seem like yours is not necessarily out of spec. I had a friend with his bindings set on the other end of the tabs and would pre release all the time. He added forward pressure to about where yours is and has not had an issue since. Disclaimer: I am not a binding tech

**This post was edited on Mar 28th 2024 at 1:58:40pm
Mar 28 2024 1:57PM
4 0
profile picture
D*A
Posts: 37 - Karma: 54
Thanks for your reply. I was always been told it should be in the middle of the dashes so I tought this.
mjkuby12After talking to multiple shops about forward pressure on the attacks, my understanding is that as long as your housing falls within the dashes on the tab you are good. It would ideally be perfectly in the middle of the dashes but it does not seem like yours is not necessarily out of spec. I had a friend with his bindings set on the other end of the tabs and would pre release all the time. He added forward pressure to about where yours is and has not had an issue since. Disclaimer: I am not a binding tech

**This post was edited on Mar 28th 2024 at 1:58:40pm
Mar 28 2024 1:59PM
0 0
profile picture
Tino94
Posts: 72 - Karma: 1,218
As long as its in the indicator range its sweet, you generally try get in the middle but if you can't it will be a choice on the tighter or looser side. Which does make it release or hold in slightly more
Mar 28 2024 2:13PM
4 0
profile picture
D*A
Posts: 37 - Karma: 54
Thanks for your reply. So maybe I should have lowered a bit my dins.

I will do that if my season is not ended :')
Tino94As long as its in the indicator range its sweet, you generally try get in the middle but if you can't it will be a choice on the tighter or looser side. Which does make it release or hold in slightly more
Mar 28 2024 2:16PM
0 0
profile picture
D*A
Posts: 37 - Karma: 54
Btw, this is what there is written in the manual.





Tino94As long as its in the indicator range its sweet, you generally try get in the middle but if you can't it will be a choice on the tighter or looser side. Which does make it release or hold in slightly more
Mar 28 2024 2:21PM
0 0
profile picture
Tino94
Posts: 72 - Karma: 1,218
Like I said if its within the range its fine just a slight difference between the start or end.
Depends how you ski the dins can still hold on pretty well even when its a low number with the right forward pressure.
I have my toes a little lower then my heels because I want those to release but its not recommend to have a different din setup
Also there is a toe height on some bindings that will affect the release if way too tight
Mar 28 2024 3:17PM
2 0
profile picture
IsaacNW82
Posts: 769 - Karma: 6,693
That looks fine. Unfortunately it is still possible to hurt your knee with a perfectly adjusted binding, because bindings were specifically designed to mitigate tib-fib fractures, not knee injuries
Mar 28 2024 4:39PM
4 0
profile picture
Tucko
Posts: 228 - Karma: 1,922
FurlansThanks for your reply. I was always been told it should be in the middle of the dashes so I tought this.

When you can't get it in the middle, go with the tighter setting. If a shop set it up, they would have torqued it too, and they would have told you if it was releasing too tight (thats what should be done, there are probably shitty shops out there that don't do that or do it wrong).
Mar 29 2024 1:04AM
2 0
All times are Eastern (-5)