Member of the Month

hi_vis360
November, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Re-using old mount holes

profile picture
patskis22
Posts: 364 - Karma: 1,148
Forgive my ignorance here.
got some old wets I’m tryna bring back to life. Will it be sufficient to re-use pre existing mount holes by sticking some glue in there or would they just rip out? If so what type of glue? Or am I better off just rotating them and mounting them with some new holes. 3 mounts on em so far so don’t really want to drill into em again.

thanks in advance
Jan 6 2024 4:06PM
1 0
profile picture
fdWEARer
Posts: 272 - Karma: 301
patskis22Forgive my ignorance here.
got some old wets I’m tryna bring back to life. Will it be sufficient to re-use pre existing mount holes by sticking some glue in there or would they just rip out? If so what type of glue? Or am I better off just rotating them and mounting them with some new holes. 3 mounts on em so far so don’t really want to drill into em again.

thanks in advance


could consider using quiver killers, or something similiar, you would drill the holes out with the new bit, then thread in the quiver quillers with epoxy, then you use machined screws to insert in your bindings, that way they are also removable at can be taken off and put back on at any time.
Jan 6 2024 4:09PM
3 0
profile picture
patskis22
Posts: 364 - Karma: 1,148
Misfitmonkeycould consider using quiver killers, or something similiar, you would drill the holes out with the new bit, then thread in the quiver quillers with epoxy, then you use machined screws to insert in your bindings, that way they are also removable at can be taken off and put back on at any time.


I forgot about that option. Thanks dude!
Jan 6 2024 4:13PM
1 0
profile picture
jca
Posts: 4172 - Karma: 6,310
As long as the existing holes aren't stripped, it's totally fine to reuse the holes. If they're stripped (spinning screws) go for the inserts or helicoil.
Jan 6 2024 5:12PM
6 0
profile picture
Jhaek
Posts: 297 - Karma: 717
And epoxy the screws in for good measure
jcaAs long as the existing holes aren't stripped, it's totally fine to reuse the holes. If they're stripped (spinning screws) go for the inserts or helicoil.
Jan 7 2024 2:13AM
2 1
profile picture
FaunaSkis
Posts: 610 - Karma: 6,599
The other option if you can’t get a regular mount with PVA glue to work in a set of previous mount holes, is plastic or brass snoli plugs.
A good service tech will be able to get you going again if you try to mount them yourself and get spinner screws.
Jan 7 2024 3:31PM
0 0
profile picture
Luke.Pascot
Posts: 12 - Karma: 51
Ive reused mount holes a number of times. I always make sure to help coil the ski. I can actually tell you straight up that a heli coil mount is stronger than just a regular hole with glue. It’s more secure, cuz the screw is biting into metal, and the helix coil takes up more surface area within the ski. Hope this helps :)
Jan 15 2024 8:24PM
0 0
profile picture
Chunderface
Posts: 2527 - Karma: 9,933
You should be able to reuse the old holes without issue. If the threads are messed up or something else is going on maybe not, but normally it is a non-issue. Use wood glue, not epoxy. I've done it before with zero issues.
Jan 16 2024 9:26AM
0 0
All times are Eastern (-5)