Member of the Month

partyandBS
December, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Nose butter ski help

profile picture
squidwardz
Posts: 33 - Karma: 25
So my skis keep releasing me when I try nose but not when I tail. I also noticed that the rear din is +1 .5 higher than my fronts. Is this normal? Or should I raise the din on fronts?


should I also raise the dins up by +1 after wards or nah
Feb 1 2023 5:03PM
2 1
profile picture
Gourd
Posts: 468 - Karma: 5,050
you can find an calculator online which will tell you your din. if you still pop out, raise it by .5, repeat.
Feb 1 2023 5:06PM
1 0
profile picture
squidwardz
Posts: 33 - Karma: 25
Thanks what about the din gap front\back
Gourdyou can find an calculator online which will tell you your din. if you still pop out, raise it by .5, repeat.
Feb 1 2023 5:11PM
0 0
profile picture
BlueVillain
Posts: 408 - Karma: 2,439
Your DIN should always be the same in the front and back, it defeats the purpose otherwise
Feb 1 2023 5:13PM
4 4
profile picture
squidwardz
Posts: 33 - Karma: 25
Dead ass or
BlueVillainYour DIN should always be the same in the front and back, it defeats the purpose otherwise
Feb 1 2023 5:14PM
0 0
profile picture
BlueVillain
Posts: 408 - Karma: 2,439
squidwardzDead ass or


I'd like to know some other opinions but from what I've been told as a tech your DIN should always be the same front and back and it makes sense to me. Why do you need them to be different?
Feb 1 2023 5:21PM
2 1
profile picture
squidwardz
Posts: 33 - Karma: 25
True true.. illl get to progressive cranking Ig
BlueVillainI'd like to know some other opinions but from what I've been told as a tech your DIN should always be the same front and back and it makes sense to me. Why do you need them to be different?
Feb 1 2023 5:26PM
1 0
profile picture
plugs
Posts: 107 - Karma: 419
BlueVillainI'd like to know some other opinions but from what I've been told as a tech your DIN should always be the same front and back and it makes sense to me. Why do you need them to be different?


Why would you crank the toes if your heels are the ones that keep releasing. Most skiers arent doing nose butters or landing switch off big jumps so the dont have the same need for heel retention. Cranking your toes just because you need more retention in the heels makes no sense.
Feb 1 2023 6:07PM
3 2
profile picture
Vish-shoe
Posts: 1949 - Karma: 14,526
Gourdyou can find an calculator online which will tell you your din. if you still pop out, raise it by .5, repeat.


🚨 Lawsuit Incoming 🚨
Feb 1 2023 6:41PM
1 0
profile picture
BradFiAusNzCoCa
Posts: 7250 - Karma: 64,053
No. I’ve had shops set pivot toes and heels separately based on the Feedback they get from the din test
squidwardzDead ass or
Feb 1 2023 7:22PM
1 0
profile picture
Non_State_Actor
Posts: 4961 - Karma: 17,820
BradFiAusNzCoCaNo. I’ve had shops set pivot toes and heels separately based on the Feedback they get from the din test


Yeah, if a shop did a release test on them the may have adjusted the fronts and rears separately to obtain consistent release values.

Where did the skis come from and also what binding are we talking about?
Feb 1 2023 7:33PM
2 0
profile picture
Farmville420
Posts: 4887 - Karma: 63,113
hey man DM me you win the giveaway
Feb 1 2023 7:57PM
0 0
All times are Eastern (-5)