Member of the Month

hi_vis360
November, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

How to replace tyrolia attack 13 brakes?

profile picture
skiit456
Posts: 46 - Karma: 150
I need to replace my brakes on my attack 13s, I already have the new pair. How do I do it without stripping any screw or anything like that.
Apr 15 2022 11:07AM
1 0
profile picture
skierman
Posts: 8369 - Karma: 7,578
BRING IT TO A SKI SHOP
Apr 15 2022 11:39AM
3 4
profile picture
skiit456
Posts: 46 - Karma: 150
skiermanBRING IT TO A SKI SHOP


I dont have acess to it right now calm your shit if you don't have an awnser then don't bother
Apr 15 2022 11:41AM
8 2
profile picture
crustyboot.420
Posts: 989 - Karma: 4,275
You gotta screw them screws out
Apr 15 2022 2:30PM
3 0
profile picture
Non_State_Actor
Posts: 4875 - Karma: 17,330
skiit456I need to replace my brakes on my attack 13s, I already have the new pair. How do I do it without stripping any screw or anything like that.

Carefully unscrew the two screws directly under the brake by hand. Then pull the brake up and forward toward the toe piece. Make sure the screw holes are clean and dry and thay the area around them is flush with the top of the ski. Reverse to install new brake. Apply a dab of high quality waterproof wood glue to the threads of the screws and screw them in carefully. The first turn or two should go smoothly if the screws are threading back in to where they were. Torque to spec (I think it's around 4nm) careful not to over-tighten. Let glue cure according to instructions. Go ski.
Apr 15 2022 2:40PM
5 0
profile picture
BradFiAusNzCoCa
Posts: 7063 - Karma: 61,877
What he said
mystery3Carefully unscrew the two screws directly under the brake by hand. Then pull the brake up and forward toward the toe piece. Make sure the screw holes are clean and dry and thay the area around them is flush with the top of the ski. Reverse to install new brake. Apply a dab of high quality waterproof wood glue to the threads of the screws and screw them in carefully. The first turn or two should go smoothly if the screws are threading back in to where they were. Torque to spec (I think it's around 4nm) careful not to over-tighten. Let glue cure according to instructions. Go ski.
Apr 15 2022 3:19PM
3 0
profile picture
Hoffhound
Posts: 230 - Karma: 1,140
I just did this with some pivots I broke and I found a YouTube tutorial that really helped! I’d recommend looking for something similar
Apr 15 2022 3:58PM
3 0
profile picture
will.irwin
Posts: 69 - Karma: 477
where can you buy replacement brakes i broke mine recently but i couldnt find any online
Apr 15 2022 6:01PM
0 0
profile picture
skiit456
Posts: 46 - Karma: 150
will.irwinwhere can you buy replacement brakes i broke mine recently but i couldnt find any online


search tyrolia attack 13 or what ever your model is 'replacement brakes' and it should pop up. make sure that you pick the right size.
Apr 15 2022 6:13PM
2 0
profile picture
SlitherySnake
Posts: 1168 - Karma: 8,614
will.irwinwhere can you buy replacement brakes i broke mine recently but i couldnt find any online


what size you need my boy
Apr 15 2022 6:39PM
0 0
profile picture
animator
Posts: 4554 - Karma: 26,266
Gotta take the screws out which is why I will never ski attacks again. Same with pivots
Apr 15 2022 8:09PM
0 1
profile picture
will.irwin
Posts: 69 - Karma: 477
SlitherySnakewhat size you need my boy


95mm
Apr 15 2022 9:50PM
0 0
profile picture
Non_State_Actor
Posts: 4875 - Karma: 17,330
animatorGotta take the screws out which is why I will never ski attacks again. Same with pivots


What do you run? STH? I've never mounted those.
Apr 15 2022 10:43PM
0 0
profile picture
animator
Posts: 4554 - Karma: 26,266
mystery3What do you run? STH? I've never mounted those.


Griffons or Pivots (pivots pretty much just for CAST)
Apr 15 2022 11:17PM
0 0
profile picture
BradFiAusNzCoCa
Posts: 7063 - Karma: 61,877
You made it seem like you didn’t like pivots in your last post.
animatorGriffons or Pivots (pivots pretty much just for CAST)
Apr 16 2022 1:13AM
2 0
profile picture
animator
Posts: 4554 - Karma: 26,266
BradFiAusNzCoCaYou made it seem like you didn’t like pivots in your last post.


which one
Apr 16 2022 2:31AM
0 0
profile picture
Non_State_Actor
Posts: 4875 - Karma: 17,330
animatorGotta take the screws out which is why I will never ski attacks again. Same with pivots


animatorwhich one


This one?
Apr 16 2022 2:41AM
0 0
profile picture
animator
Posts: 4554 - Karma: 26,266
mystery3This one?


Oh yeah lmao I’m an idiot

thats why I included the *just for CAST* my skis with CAST aren’t used in the park and shit so they don’t get beat up as hard, therefore the brakes tend to last longer. Any park skis usually get griffons just because the pivot brakes are kinda eh even though I’m not a hardcore park skier
Apr 16 2022 2:49AM
1 0
profile picture
SlushSeason
Posts: 885 - Karma: 6,703
Bumping this dead thread
Has anyone had good luck bending brakes back to shape? Do you just put it in a vice and yank on it with pliers?
My attack 13 brake is dragging and i can't bend it back while it's in the binding
Jan 19 2024 2:16PM
2 0
profile picture
will.irwin
Posts: 69 - Karma: 477
Yeah that should do it there pretty easy to bend. You could probably heat it up a little if it wasn’t bending too
SlushSeasonBumping this dead thread
Has anyone had good luck bending brakes back to shape? Do you just put it in a vice and yank on it with pliers?
My attack 13 brake is dragging and i can't bend it back while it's in the binding
Jan 20 2024 10:55PM
0 0
profile picture
Non_State_Actor
Posts: 4875 - Karma: 17,330
SlushSeasonBumping this dead thread
Has anyone had good luck bending brakes back to shape? Do you just put it in a vice and yank on it with pliers?
My attack 13 brake is dragging and i can't bend it back while it's in the binding

Use a thin pipe ~1/2" or a cut off ski pole to provide leverage.
Jan 21 2024 12:08AM
1 0
All times are Eastern (-5)