Restless — An Alex Hall Portrait (Full Film) | Faction Skis
  • Forums
  • Gear Talk
  • Extracting a snapped binding screw, or fuqqq it just ride with one down

Member of the Month

KilaTsunami
October, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Extracting a snapped binding screw, or fuqqq it just ride with one down

profile picture
alpineplease
Posts: 2791 - Karma: 1,789
Last night tossed some old Rossi FKS 120s on some Bdog Edgeless. I salvaged screws from another P18 binding that were quite old, and in the process of putting them on, then double checking boot fit (first install) then taking them out, epoxying them in, a heel bolt snapped in the ski. In my whiskey induced haze, I screwed the rest on and called it a night.

Then I woke up at 3am. How the hell do you get this thing out! Or better yet - has any one ridden with one of these missing?

See photo - I put some expoxy in the hole. Ride it and find out?


Apr 14 2021 11:53AM
7 0
profile picture
TheWeaz
Posts: 803 - Karma: 1,903
depends how hard you are going to crash if the heel rips out, are you going to knock your front teeth out on a concrete ledge?

Pivots already have a pretty small mounting pattern, with 3 screws instead of 4 your kinda asking for problems.

that said getting that out is going to be a huge pain and will probably mangle the hole enough that you would need to use a heli coil to re use that hole.
Apr 14 2021 12:23PM
8 0
profile picture
.nasty
Posts: 10581 - Karma: 11,157
Take the heel piece off and try using a screw extractor that you can find at a hardware store.


Apr 14 2021 12:24PM
6 0
profile picture
profa_212
Posts: 8904 - Karma: 35,918
.nastyTake the heel piece off and try using a screw extractor that you can find at a hardware store.




This. Then throw a helicoil in there with a new screw. Should be good after that
Apr 14 2021 1:16PM
9 0
profile picture
Chrischi69
Posts: 652 - Karma: 5,062
Im kind of a pussy about my gear but i would not ride that
Apr 14 2021 3:12PM
5 0
profile picture
No.Quarter
Posts: 5257 - Karma: 16,962
alpinepleaseepoxying them in, a heel bolt snapped in the ski. In my whiskey induced haze, I screwed the rest on and called it a night.

This is going to make your task much more difficult if you try to use a screw extractor. Even getting the screws that aren't busted out could be difficult. If a screw extractor doesn't work you may need to try and drill it out, but I'd anticipate killing a couple of drill bits.
Apr 14 2021 3:20PM
1 0
profile picture
alpineplease
Posts: 2791 - Karma: 1,789
Well Newschoolers you seem like a loose crowd but the overwhelming support to fix this issue resulted in doing just that.

went in at lunch, drilled out the snapped screw, tapped it out with an extractor. Epoxy hadn’t set - install was last night - so they came out easily and were reinstalled nicely.


so now, we’re in business. Epoxy will set by afternoon tomorrow and I’ll grind a concrete ledge for y’all and let you know what shape my teeth are in.

I have an underbite after all and am trying to fix it...
Apr 14 2021 11:05PM
5 0
profile picture
anders_a
Posts: 1680 - Karma: 5,603
I'd remove binding, then punch it and use a LINKS drillbit to open it up for the pigdicks (screw extractor)


pivot narrow mounting pattern with 3 bolts? no bueno!
Apr 15 2021 3:09AM
0 1
All times are Eastern (-5)