Member of the Month

partyandBS
December, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

DIY Ski Mitts

profile picture
iced
Posts: 3070 - Karma: 17,980
Does anyone have any resources/experience in this? Looking to compile some resources and maybe post however i figure it out

damn gloves keep shredding
Feb 11 2020 4:36PM
3 0
profile picture
xxACIDTRIPxx
Posts: 5980 - Karma: 8,175
I fill plastic bags with housing insulation (the pink wool stuff) then just chuck my hands in them.
Feb 11 2020 4:40PM
10 0
profile picture
Andi_G
Posts: 3086 - Karma: 15,114
Buy oven mitts and then duct tape around em for waterproofing
Feb 11 2020 4:51PM
5 0
profile picture
elcheapo
Posts: 3449 - Karma: 13,976
Buy oven mitts, cheaper than the materials and hassle. 50$on amazon.
Feb 11 2020 5:15PM
0 0
profile picture
No.Quarter
Posts: 5257 - Karma: 16,965
Insulated leather Kincos have been the most durable I've found if you are prone to shredding gloves. They are like $20 - $30 bucks at a hardware store so not too big of a deal to replace them.
If you really wanna go DIY, you could figure out some way to protect the palms with some extra leather.
Or maybe rough up the palms a lil bit with some coarse sandpaper and then do a coating of shoegoo before doing a few coats of snoseal
I'm assuming you are shredding them from a rope tow or something.
Feb 11 2020 6:00PM
0 0
profile picture
GayWolf420
Posts: 37684 - Karma: 123,679
if you do end up gathering good materials, maybe a design or a material where the inner warm lining doesnt pack out as much, especially for a work/lifty style riding mitt. also padding on like the knuckles/thumb area for when youre getting spicy in the trees
Feb 11 2020 7:13PM
0 0
profile picture
OregonDead
Posts: 6949 - Karma: 25,109
buy the Kincos or if you are a hunter or trapper make your own out of hide. my guess is nutria is actually really good for this and your local authority will probably be on board with free nutria hunting
Feb 11 2020 7:19PM
0 0
profile picture
clindblomskier
Posts: 686 - Karma: 5,141
Wells Lamont mitts are not very expensive and have major drip. Another idea is to go to your local farm supply/hardware store and get some winter work mittens for like 20$ (they’ll be indestructible) and then coat them in snoseal
Feb 11 2020 10:19PM
3 0
profile picture
Idahoe
Posts: 1027 - Karma: 7,538
Kincos baby
Feb 12 2020 1:36PM
1 0
profile picture
profa_212
Posts: 9004 - Karma: 37,364
AndrewGravesSVBuy oven mitts and then duct tape around em for waterproofing


did this when i broke my wrist/hand. Worked wonderfully. Also had to duct tape my pole to that band which was pretty funny.
Feb 12 2020 6:25PM
2 0
profile picture
clorox
Posts: 1728 - Karma: 4,863
I cut the liners out of some old Kinco axemen. My mom knit me some mittens for christmas and sewed the finger tips in to get them to stay. Real warm and comfortable but I only use them w/o poles cause that feels a little weird since I've started using gloves again.
Feb 12 2020 6:48PM
0 0
profile picture
CalumSKI
Posts: 4216 - Karma: 24,314
Afghan_kushI fill plastic bags with housing insulation (the pink wool stuff) then just chuck my hands in them.


your hands would be so itchy wtffff lol
Feb 12 2020 8:53PM
1 1
profile picture
50Kal
Posts: 2835 - Karma: 5,534
icedDoes anyone have any resources/experience in this? Looking to compile some resources and maybe post however i figure it out

damn gloves keep shredding

Like sewing you own mitts or just water proofing them?

I know a buddy who traps, then turns critters into super warm over mitts. Sewing leather is extremely difficult, even with a industrial sewing machine.

For water proofing get snow seal and rub it into your leather gloves. If your super careful you can warm them up in a oven. Just don't drip snow seal in the hot oven. It will smoke bad.
I would highly recommend double up on aluminum drip sheets.
Feb 12 2020 10:04PM
0 0
profile picture
iced
Posts: 3070 - Karma: 17,980
50KalLike sewing you own mitts or just water proofing them?

I know a buddy who traps, then turns critters into super warm over mitts. Sewing leather is extremely difficult, even with a industrial sewing machine.

For water proofing get snow seal and rub it into your leather gloves. If your super careful you can warm them up in a oven. Just don't drip snow seal in the hot oven. It will smoke bad.
I would highly recommend double up on aluminum drip sheets.


im looking to sew
when i see shit like salmon arms and kico i think how hard can it be
i plan to reuse an inside im just gonna sew an outside
Feb 12 2020 10:08PM
0 0
profile picture
ronders_
Posts: 568 - Karma: 2,325
I usually buy those $15 leather mittens you find up North in hunting stores and gas stations. They stand up to the rope for a while, cheap so you don’t have to worry, and pretty warm
Feb 12 2020 10:31PM
1 0
profile picture
notadoctor
Posts: 408 - Karma: 663
You can buy leather scraps from tandy. You can probably find scraps big enough for mitts. They might have some patterns or instructions there too.

It was mentioned before but you can't sew it easy, most machines won't be able to do it so you'll likely end up doing it by hand.

Sounds like an interesting project though, keep us updated on your progress.
Feb 13 2020 6:21PM
0 0
profile picture
iced
Posts: 3070 - Karma: 17,980
notadoctorYou can buy leather scraps from tandy. You can probably find scraps big enough for mitts. They might have some patterns or instructions there too.

It was mentioned before but you can't sew it easy, most machines won't be able to do it so you'll likely end up doing it by hand.

Sounds like an interesting project though, keep us updated on your progress.


Thanks for that tandy source, I'm actually a short drive from mississauga
the way . its looking, im likely going to try a canvas/knit/leather combo, to reduce the hand sowing
Feb 13 2020 10:14PM
1 0
All times are Eastern (-5)