Member of the Month

partyandBS
December, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Edge bevel?

profile picture
whashisface
Posts: 298 - Karma: 10
Just wondering what angle people use for their base edges? Do you just keep it standard (90 degrees) or do you have it more beveled?
Dec 27 2004 1:17PM
0 0
profile picture
CrystalineSkier
Posts: 1065 - Karma: 16
beveled, not really, i don't know anyone but my little brother who has ever done it. If you angle the edge more you get a 'sharper edge' which 'increases your grip' but you really don't need it. Just keep care of your skis and your fine.
Dec 27 2004 1:20PM
0 0
profile picture
whashisface
Posts: 298 - Karma: 10
I mean angling it down from the base (when your base is at the top) so that there's less grip. Should I just leave it flat?

Dec 27 2004 2:09PM
0 0
profile picture
ifsa_alum
Posts: 355 - Karma: 10
Whashisface, I read that over and over and still don't know which angle you're talking about. Generally, most skis come like this:
1° base edge bevel
1° side edge bevel
90° edge angle (square)

which is fine for everyday use.

FYI, I ride my S-LAB's:
1° base edge bevel
3° side edge bevel
88° edge angle (acute)

I ski east coast hardpack most of the time so I prefer the bite of a "sharper" edge.

Normally, you don't want the base bevel to be 0° (flat to the ski base) because the skis will grab hard and rail. Practically impossible to slip/slide, shuss, or butter.

--------

This is Whistler, as I'm getting my ass whooped by Jon - I fuckin' hate that guy - that guy wins all the time.

- The Dumont (skier commentary in High Five)
Dec 27 2004 3:37PM
0 0
profile picture
ifsa_alum
Posts: 355 - Karma: 10
Here are some illustrations to help clarify:

Standard:


Mine:

--------

This is Whistler, as I'm getting my ass whooped by Jon - I fuckin' hate that guy - that guy wins all the time.

- The Dumont (skier commentary in High Five)
Dec 27 2004 3:53PM
0 0
profile picture
KickerTheCanMan
Posts: 207 - Karma: 10
^ He's right. If it's skis for real skiing, the more side bevel the more control you get, and base bevel is normally 1 degree. If yur doing jibbing 1 degree side and base is pretty much the way all skis come, and once they've been railed there's no point in tuning them anyway because they'll be round. Just keep em deburred so they don't catch.

'180 net grab = NOT a new trick!'

Have you ever seen a little kid slide back down the inrun of a kicker without going over? This is why parents shouldn't dump their kids off anywhere near the park...
Dec 27 2004 3:56PM
0 0
profile picture
whashisface
Posts: 298 - Karma: 10
Cheers. Sorry for the confusing post, read it in a book and wasn't sure how it'd apply to freestyle. I was talking about base edge bevel. I'll leave my edges alone.
Dec 27 2004 5:40PM
0 0
profile picture
CTD
Posts: 6301 - Karma: 350
base bevels help on jib skis, specially if your doin nose and tail presses.



i looked on google but all i could find was 3D Animation porn-sxmarty6



ECS headwear, hit me up!
Dec 28 2004 12:53AM
0 0
profile picture
McGoo
Posts: 227 - Karma: 10
After doing rails, your edges will look like the rounded off blue corners in the diagram. When that happens, base angles dont mean shite.



In tractor pulls, a 'full pull' is the best you can get. Ahh, how sport mirrors life.
Dec 28 2004 8:26AM
0 0
profile picture
dutch1
Posts: 465 - Karma: 11
actually, nearly every ski company factory tunes their skis 1 degree base, 2 degree side bevel... with a few exceptions: atomic tunes all their skis to a 1 degree base and a 3 degree side and a few others i don't remember off the top of my head at the moment...

however, as far as the base edge applies you aren't going to want anything greater than a 1 degree base bevel. A lot of racers have their skis tuned to a 0 degree base bevel or even have a 1 degree bevel to a -1 degree bevel (if that makes sense)... it would kinda look like this: /\ (i said kinda...)

but, yeah, no need to change your base bevel...


'Because it is there...'
-George Leigh Mallory
Dec 28 2004 10:23PM
0 0
profile picture
freeskinow
Posts: 617 - Karma: 12
line recommends a 2 degree side edge bevel and a 1 degree base edge bevel





'You've got to run like an antelope, out of control'
Dec 28 2004 11:45PM
0 0
profile picture
ifsa_alum
Posts: 355 - Karma: 10
Here's the most complete list I can find on factory settings:
Brand/base/side
Atomic 1 3
Dynastar 1 1-2
Elan .5-1.5 0-2
Evolution 1 1
Fischer 1 3
Hart .5 1.5-2
Head 0-1 0-2
K2 .5 1 (K2 told me 1 and 1)
Line 1 2
Olin 1 1
Nordica .5 1.5
Rossignol 1 1
Salomon 1 1
Stockli 0-.5 1
Volant 1 1
Volkl 1 2



--------

This is Whistler, as I'm getting my ass whooped by Jon - I fuckin' hate that guy - that guy wins all the time.

- The Dumont (skier commentary in High Five)
Dec 28 2004 11:53PM
0 0
profile picture
devine
Posts: 1720 - Karma: 11
^ u are a bevel god



member#13687



'i just rented good will hunting , how is it?'

'lets put it this way, even matt damon cant make it suck.'

'matt damon? hes in con air right?'

'yes , yes he is.'
Dec 29 2004 10:59AM
0 0
All times are Eastern (-5)