Member of the Month

hi_vis360
November, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Fixing a de-lamming ski?

profile picture
Milesmax
Posts: 127 - Karma: 99
What's up guys, i have a question for you all. If you're ski JUST started delaying is there anything you can do to stop it from progressing and keeping your cores dry? could you just re-oppxy and clamp you layers??
Mar 5 2014 2:27PM
10 1
profile picture
NMMedia
Posts: 982 - Karma: 1,700
dry it out, put a thin layer of epoxy on one of the surfaces (epoxy works best thin). Clamp the shit out of it for like 2 days (needs plenty of time to set). Then put a couple rivets in it if you can, the epoxy will do ok but it will start to delam again if you don't put something solid in there. Good luck!
Mar 5 2014 2:40PM
2 0
profile picture
Park_Mho
Posts: 351 - Karma: 390
You can use epoxy and clamp it, but I would recommend 24hr epoxy instead of the 5 min stuff. If you leave the skis out in the sun for a long time and it is warm outside, the epoxy can undo itself.
Mar 5 2014 3:47PM
1 0
profile picture
ChristianMingle
Posts: 629 - Karma: 1,202
Where can you get rivets? one toe on my ski is delamming pretty badly and i keep epoxying it but that obviously is just a temp fix, I want to rivet but have no idea what to get or where to get them.
Mar 5 2014 4:28PM
1 0
profile picture
Keith.
Posts: 967 - Karma: 88
To use rivets you need a rivet gun. So you can either buy one of these http://www.canadiantire.ca/en/pdp/stanley-contractor-grade-riveter-0584703p.html#.UxeeD_ldWSo and a pack of rivets like this http://www.canadiantire.ca/en/pdp/mastercraft-steel-rivets-0584719p.html#.UxeeG_ldWSo

Alternatively if you dont want to buy that, you can use a small bolt or better something called a chicago screw.

That said, using a small bolt is not ideal, the heads extrude and can and will catch on each other once and while when your skis cross (sketchy as fuck). Speaking from experience here.

IMO rivets are best and chicago screws are pretty legit as well.
Mar 5 2014 5:04PM
2 0
profile picture
ChristianMingle
Posts: 629 - Karma: 1,202
Thanks man +K. Anyone got a link to those (or similar) rivets in for sale in the US?
Mar 5 2014 8:09PM
1 0
profile picture
milk_man
Posts: 5252 - Karma: 5,978
Duct tape the ends. Thats what this guy that goes to my hill did
Mar 5 2014 8:25PM
0 1
profile picture
TimRiley
Posts: 1873 - Karma: 1,327
you can buy the riveter and rivets at home depot
Mar 5 2014 8:50PM
1 0
profile picture
NMMedia
Posts: 982 - Karma: 1,700
Go to any hardware store, Home Depot, Lowes, Ace. They should be able to point you to a rivet gun and rivets, they usually aren't that expensive. Hell of a lot less expensive than new skis for sure.
Mar 6 2014 1:14PM
1 0
profile picture
Milesmax
Posts: 127 - Karma: 99
Thanks guys, this helped a lot. +k to all of you
Mar 11 2014 5:28PM
0 0
All times are Eastern (-5)