Member of the Month

KilaTsunami
October, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Marker griffon question

profile picture
Pu-Tang
Posts: 848 - Karma: 647
Are marker griffons adjustable? so I have a bigger full tilt and I wanna make the binding smaller by like 15mm is that possible?
Dec 18 2013 11:17PM
36 6
profile picture
cwphoto
Posts: 2332 - Karma: 780
first for bishop


but yeah the heel piece can slide a few cm
Dec 18 2013 11:18PM
0 0
profile picture
rememberscott
Posts: 1291 - Karma: 5,201
makes sense
Dec 18 2013 11:30PM
10 1
profile picture
Turd.Ferguson
Posts: 1437 - Karma: 2,713
side effects of finals week?
Dec 18 2013 11:58PM
3 0
profile picture
Casey
Posts: 7847 - Karma: 24,308
just buy a cheap heat gun and start heating the heel piece until it starts to slide in the track, probly will only take like an hour on high.
Dec 19 2013 12:13AM
6 1
profile picture
Dr.Dickless
Posts: 2620 - Karma: 1,392
This one really belongs in gear talk
Dec 19 2013 12:14AM
3 0
profile picture
HuckNorris44
Posts: 1025 - Karma: 2,393
^This. Also, 15mm is a lot to adjust a binding. You'll have to remount them to fit that small of a boot. Most bindings wont adjust that much.
Dec 19 2013 2:34AM
2 0
profile picture
doyle.
Posts: 1624 - Karma: 596
it really depends on where the heel piece is on the track right now. you may have to remount them, you may not
Dec 19 2013 2:53AM
0 0
profile picture
VerticalDrop
Posts: 324 - Karma: 4,479
lolololololololololol
Dec 19 2013 6:43PM
1 1
profile picture
NPCPLUS
Posts: 162 - Karma: -155
you want to make the binding smaller, for your bigger boots....
Dec 19 2013 6:46PM
1 0
profile picture
Substitute
Posts: 1376 - Karma: 2,275
Make sure that your boot is not too small or too big. I had the same issuse with my boots/bindings. I had to move my binding like 10 cm. there is a very small threshold of ajustability in griffons. Mabye a few cm at best. If you put your boot in the binding and there is a large amount of silver half cork screwing looking playe then you will need to re-mount the heel peice.

Also if you are moving the screw and it moves then if stops adjusting, you have reached the end of the travel and must re-mount. This is a pain in the ass but is very easy to do. But unless you have experience mounting bindings, nust bring them to a shop. (No ofdence but it would apear that you would not. Considering you did not know if your bindings adjusted. Which is fine.)

I really hope this helped. If it did not message me with questions
Dec 19 2013 7:01PM
0 0
profile picture
Substitute
Posts: 1376 - Karma: 2,275
^mm not cm.
that would be an insane amount of adjusting.
Dec 19 2013 7:02PM
1 0
profile picture
HuckNorris44
Posts: 1025 - Karma: 2,393
The back screw on the heel piece that is used to adjust the binding need to be flush with the housing when the boot is secured in the binding. When the screw is flush, the forward pressure is set correctly. If this cannot be achieved by moving the heel piece, then you need to remount them. Plain and simple
Dec 20 2013 3:16AM
1 0
profile picture
Pu-Tang
Posts: 848 - Karma: 647
I'll prolly eject right out of them when I go skiing tomorrow.
Dec 20 2013 6:48AM
0 1
profile picture
GPO
Posts: 656 - Karma: 296
after some googling

Dec 20 2013 7:35AM
1 0
profile picture
lands11
Posts: 1818 - Karma: 1,677
This actually didn't work for me. I had to get a small torch and use it on low before I got it to slide.
Dec 20 2013 8:59AM
2 1
All times are Eastern (-5)