Member of the Month

Biffbarf
March, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Please Help! How to fix my destroyed skis? +kkkk

profile picture
BROBRO
Posts: 563 - Karma: 1,245
Click for larger image

So here is my problem, these skis were new last season and after about a week there were cracks on each edge under foot about, ten cracks per ski. once spring came around and we were riding slush the base began to disconnect from the ski because water was getting in through the cracks and under the base. After a few days riding this season one part of the bubbled up base finally split so i cut it and p-texed it. Well that didn't last one day and now on the inside of the ski it has actually cracked through the core. I still want to be able to ride theses skis for urban and what not. What do you recommend I do? What I was thinking was to epoxy the crack then but like 2 small screws through the sidewall to link the crack up and then either p-tex the missing base or just leave it. Would that work? PLEASE HELP ME!!!


12 years ago
1 0
profile picture
GuacamoleMane
Posts: 1421 - Karma: 2,013
im sorry, but what kind of shitty skis did u buy?
12 years ago
0 0
profile picture
BROBRO
Posts: 563 - Karma: 1,245
2010 atomic punx the punx have since upgraded to a beefy edge so they are better now the edges on these were pretty tiny.
12 years ago
0 0
profile picture
manzear
Posts: 843 - Karma: 849
if they are going to be a urban ski, fill with p-tex or epoxy and that about all you can do. Those look pretty messed up. Once water gets in there and the serious cracks start to happen, you're kind of screwed.
12 years ago
0 0
profile picture
Forcillo
Posts: 3801 - Karma: 3,580
Not trying to call you out here, but I've had my 09 punx for over 2 years and have had not durability problems, other than topsheet chipping. Did you ever wax?
12 years ago
0 0
profile picture
andrewblackie
Posts: 292 - Karma: 109
As a dryslope skier, I can definitively say the only effecting thing to stop your skis falling to pieces is epoxy resin.
12 years ago
0 0
profile picture
[YEAH]
Posts: 152 - Karma: 410
Yes we did wax fairly often, the only thing that we didn't do was detune the edges to prevent cracking. Being from the midwest rails are pretty much all we hit so skis can take some abuse.
12 years ago
0 0
profile picture
andrewblackie
Posts: 292 - Karma: 109
Sorry for the dub post, but if you can, let epoxy dry beside a dehumidifier, it sets much harder.
12 years ago
0 0
profile picture
Mag
Posts: 8155 - Karma: 14,798
You don't take anywhere near the same force on a dryslope as you do when doing urban/skiing a proper mountain.
12 years ago
0 0
profile picture
PaleCelery
Posts: 7228 - Karma: 609
Lots of epoxy. Use some tape to make a guide where you dont want the epoxy to be. Also, I reccomend using whatever epoxy has the LONGEST cure time, it will be the strongest bond. If you hit it with a heat gun right after you apply it and its still liquidy, it will become MORE liquidy and sink into where it needs to go and the air bubbles will come out. Then use 2 thin wax scrapers to protect the ski (lol) and some then clamp it up, let is cure and then once its cured clean it all up, wax em and you'll be good to go.

FYI Im a ski tech, Ive done repairs like this before, and it WONT last. But for urbans, you'll get some more life out of them at least.
12 years ago
0 0
profile picture
andrewblackie
Posts: 292 - Karma: 109
Haha yeah, maybe, but you're forgetting that dryslope makes your bases like playdough?
12 years ago
0 0
profile picture
FatWhore
Posts: 2213 - Karma: 1,098
Ryan, this seems legitt
12 years ago
0 0
profile picture
RudyGarmisch
Posts: 25444 - Karma: 13,855
100% what I'd do, but make sure its UHMW plastic for those scrapers, other plastics could bond to your ski rather well with all that epoxy...
12 years ago
0 0
profile picture
PaleCelery
Posts: 7228 - Karma: 609
I use wax paper in between that and the ski, forgot to mention that
12 years ago
0 0
profile picture
RudyGarmisch
Posts: 25444 - Karma: 13,855
I'll have to try that, UHMW is great but its too soft to distribute force evenly on large areas, at least without a ton of clamps.
12 years ago
0 0
All times are Eastern (-4); Currently it's 9:30AM