Member of the Month

KilaTsunami
October, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Where to buy a cheap rail??

profile picture
fennjack
Posts: 286 - Karma: 129
I'm looking for a double kink or handrail under $100, and around 10ft. Any ideas where to buy?
Feb 13 2012 10:19PM
0 0
profile picture
northeast
Posts: 2119 - Karma: 254
your town library or high school is a good bet.

no but foreal go to the hardware store and get some PVC pipes and 2x6es
Feb 13 2012 10:47PM
0 0
profile picture
lukewalnuts
Posts: 2730 - Karma: 152
.
Feb 13 2012 10:50PM
0 0
profile picture
fennjack
Posts: 286 - Karma: 129
If i go to hardware store I still need welding set up don't I?
Feb 13 2012 10:52PM
0 0
profile picture
@skiinmitch
Posts: 2781 - Karma: 78
PVC=Plastic tubing they use in plubing basically.

do u know anything about construction.

if you want a metal rail you will have to weld yes.
Feb 13 2012 10:55PM
0 0
profile picture
fennjack
Posts: 286 - Karma: 129
ya I'm looking for metal. How about a skateboard rail.
Feb 13 2012 11:31PM
0 0
profile picture
TACO-DOG.exe
Posts: 11988 - Karma: 12,261
you wont get that much metal for that cheap. either change your materials list or raise your budget on metal.
Feb 13 2012 11:37PM
0 0
profile picture
fennjack
Posts: 286 - Karma: 129
k thanx for the help. karma+
Feb 13 2012 11:45PM
0 0
profile picture
@skiinmitch
Posts: 2781 - Karma: 78
this. And if you want to make your own rail also you will have to get a welder which will cost even more. my suggestion go with pvc. get the stronger pvc no the flimsy ones.
Feb 13 2012 11:46PM
0 0
profile picture
fennjack
Posts: 286 - Karma: 129
So skate rails= NO
Feb 13 2012 11:59PM
0 0
profile picture
ShabbaRanks
Posts: 998 - Karma: 65
not really, find scrap metal. I hope you know to not get aluminum though or else thats a lot of money down the drain
Feb 14 2012 12:06AM
0 0
profile picture
Phil-X-
Posts: 7205 - Karma: 14,399
look on craigslist for rails.
Feb 14 2012 12:17AM
0 0
profile picture
@skiinmitch
Posts: 2781 - Karma: 78
You could use a skate rail. If u really wanted to.
Feb 14 2012 12:27AM
0 0
profile picture
Casey
Posts: 7847 - Karma: 24,308
Not necessarily. We made a skate rail out of plumbing pipe, it was galvanized steel I believe, but, you buy a pipe with a threaded end, and then a 90 degree fitting angled towards the ground attach another pipe to get your desired height, then thread on a T and have pipes going off of each end of the T for the base. The rail we had went to the ground, but you could figure out a way to prop up the other end with some creative solution, IE, predrill a hole an bolt something on the underside and go from there.
Feb 14 2012 12:34AM
0 0
profile picture
fennjack
Posts: 286 - Karma: 129
Good stuff
Feb 14 2012 12:38AM
0 0
profile picture
DUKES
Posts: 5150 - Karma: 691
i believe its called railwerx.com

Feb 14 2012 2:53PM
0 0
profile picture
Mr_Hyde
Posts: 337 - Karma: 121
Junkyard !! Make sure not to get Galvanize, fumes can kill you are make you really sick.. Look for some with a little rust on them, there more then Lilkly to be steel and not have a Galvanize coating. Just pick out the stright ones and make sure there's no dimples or dents, for a straight slide. Make friends with a welder or find a friends dad that's a welder.
Feb 14 2012 7:47PM
0 0
All times are Eastern (-5)