Member of the Month

hi_vis360
November, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Mounting FKS with a paper jig?

profile picture
tbayskier
Posts: 1138 - Karma: 1,642
I'm swapping my FKS bindings from my Line Anthems to Scott Punishers, can i trace a paper jig from anthems and then tape it square onto the punishers to mount em up?  I'll be using the same boots...just trying to save 40 bucks.  I have access to the correct drill bit.
Dec 12 2011 1:32PM
0 0
profile picture
RudyGarmisch
Posts: 25443 - Karma: 13,844
How are you going to drill the holes perfectly straight?
Dec 12 2011 1:34PM
0 0
profile picture
tbayskier
Posts: 1138 - Karma: 1,642
Using a square.  I'd grab a standard sheet of printer paper, tape it square over the binding less anthems, trace the holes, then tape the paper onto the Scotts and drill er up.  Pretty sure it would wind up crooked, I'm just curious if it is possible to do right somehow.  Thanks for the response.   
Dec 12 2011 1:37PM
0 0
profile picture
Caucasian_Asian
Posts: 2447 - Karma: 1,665
It's possible.  People use paper jigs all the time. 
I would practice a shit-ton first though.


Have you ever drilled and mounted a pair of skis before?
Do you own a posidrive as well?
Dec 12 2011 1:43PM
0 0
profile picture
tbayskier
Posts: 1138 - Karma: 1,642
i have mounted skis before, but only with real jigs.  I would practice a lot on shit skis i have lying around.  sounds good, any thoughts on how to get it perfectly straight? 
Dec 12 2011 1:44PM
0 0
profile picture
Caucasian_Asian
Posts: 2447 - Karma: 1,665
You can find paper jigs to download online.  Do that rather than tracing your current mount.  Make sure you check to see that your scale is correct after you print it out, otherwise your holes will be wrong.

Measure two or three times and then tape your template onto your skis.
Some drills have a bubble level in the handle to make sure that the drill is plumb.  This helps to ensure that your holes do not get drilled crooked.
Dec 12 2011 1:49PM
0 0
profile picture
tbayskier
Posts: 1138 - Karma: 1,642
great.  thank you.  and my drill has the bubble level. 
Dec 12 2011 1:51PM
0 0
profile picture
NWilkins
Posts: 246 - Karma: 81
I just got a pair of FKS 140's and they came with a sticker jig/template........maybe try and get a hold of one of those?
Dec 12 2011 1:52PM
0 0
profile picture
tbayskier
Posts: 1138 - Karma: 1,642
sick will do

Dec 12 2011 1:53PM
0 0
profile picture
RudyGarmisch
Posts: 25443 - Karma: 13,844
Drill the mount pattern through a 2x4 or something first.
Dec 12 2011 1:59PM
0 0
profile picture
a_pla5tic_bag
Posts: 9217 - Karma: 5,399
yeah at least use wood or something. it's pretty hard to keep the drill straight even with the bubble level.
Dec 12 2011 2:03PM
0 0
profile picture
skithesprings
Posts: 9086 - Karma: 1,349
go here, follow the directions.

http://www.tetongravity.com/forums/showthread.php/153971-Binding-Mount-Paper-Templates
Dec 12 2011 2:41PM
0 0
profile picture
stickerman
Posts: 2043 - Karma: 147
yup. mine came with this as well.
Dec 12 2011 3:12PM
0 0
profile picture
smuggs
Posts: 6561 - Karma: 1,375
paper jigs are easy just make sure to start your holes with a hammer and chizzle thing and remember that skis with metal use a different drill bit. also i eyeball out a duct tape drill bit stopper to not drill through the base. you might as well epoxy your binding screws in to.
Dec 12 2011 3:21PM
0 0
profile picture
fragglemuffin
Posts: 3312 - Karma: 444
I just mounted mine using the TGR paper jig...as long as you measure multiple times and are somewhat handy, you shouldn't have a problem.
Dec 12 2011 3:40PM
0 0
profile picture
Balto
Posts: 25985 - Karma: 4,404
you should make your own jig out of plexiglass
Dec 12 2011 3:40PM
0 0
profile picture
TheClap.
Posts: 21671 - Karma: 4,158
so that doesnt count for 98% of NS
Dec 12 2011 3:42PM
0 0
profile picture
Chompo.
Posts: 4952 - Karma: 88
I have used the paper jigs as well.. Then again I do have access to a drill press and all the proper tools/bits which makes things a lot easier.
Dec 12 2011 3:57PM
0 0
profile picture
-AP-
Posts: 819 - Karma: 344
I did the same thing with the TGR template. I practiced alot but ended up messing up and drilling an extra hole. I was lucky the extra hole was far enough away to not be a problem. Practice alot first, I'm still not sure if it's worth the $40. REI only charges $30 for mounts too and they do a good job.
Dec 12 2011 4:08PM
0 0
profile picture
SteezoSaurus
Posts: 2630 - Karma: 2,670
Srsly?

Click for larger image
Dec 12 2011 4:11PM
0 0
profile picture
skier_boy26
Posts: 11295 - Karma: 502
I'll echo the same advise: take your time and measure till you're sick of measuring. Finding the center of the ski can be tricky; it is really easy to get off-center. That said, using the TGR paper template is pretty straight forward. I've mounted all my recent skis sans jig and they have worked great.
Dec 12 2011 5:50PM
0 0
profile picture
monkatizer
Posts: 4704 - Karma: 1,518
haha
Dec 12 2011 6:03PM
0 0
profile picture
twsnow22
Posts: 1285 - Karma: 488
I've mounted tons of skis with a paper jig..no problems yet..ha.. just measure like 80 times..use a drill press.. or take them to rei.. legit mounts. sometimes they have discounts during their sales too..15$ mounts happen occasionally.
Dec 12 2011 6:16PM
0 0
profile picture
-AP-
Posts: 819 - Karma: 344
Hahahaha in my experience I've had no problems. That's embarrassing though
Dec 12 2011 6:25PM
0 0
profile picture
I.B
Posts: 8137 - Karma: 24,355
This idea right here.

I'm doing it. WIll post pics later
Dec 28 2011 11:06PM
0 0
profile picture
yoke
Posts: 150 - Karma: 5,504
Paper jigging is the way to go. Just triple check everything and make sure you have the right tools/bit.
Dec 28 2011 11:42PM
0 0
profile picture
stupendous-man
Posts: 8637 - Karma: 13,293
same here, plus it was like $10 for some reason... just make sure you tell the tech like 5 times if you want them mounted center or wherever you want them mounted. they always forget for some reason
Dec 29 2011 12:05AM
0 0
profile picture
ARspinna
Posts: 803 - Karma: 27
use a jig, haha
Jul 8 2012 4:55PM
0 0
profile picture
rozboon
Posts: 1642 - Karma: 868

Just mounted some Hellbents with FKS the other day using the paper jig from bindingfreedom.com

Triple-check your printer scaling if you're doing it this way.

Hardest bit was getting the exact (enough) centre to work from. Everything is made easier by using a nail or a punch to make a slight dent in the topsheet then use that to centre the paper jig.

A pair of calipers really helped triple-check things were where we wanted them to be as well.

Do you have a collared drillbit or some other way of ensuring you don't drill right through the ski?

Jul 8 2012 8:58PM
0 0
profile picture
Pretzel___Slaya
Posts: 1432 - Karma: 190
They changed their prices everywhere, it's $40 for members and $50 for non-members. I spent way to much money having them mount 2 of my skis, would have done it on my own if I knew of the paper templates.
Jul 8 2012 9:51PM
0 0
profile picture
nstubler
Posts: 840 - Karma: 1,170
I mounted my fks with a paper jig just fine.
As someone said above, just start your holes with a hammer and chisel and they'll be fine
Jul 8 2012 10:50PM
0 0
profile picture
DHogg
Posts: 3462 - Karma: 237





Here is a good video on how to use the paper templates. The video is from the guy who made all the templates on TGR. He isn't mounting fks but its all the same.

Jul 9 2012 12:28AM
0 0
profile picture
zerospinskier
Posts: 4867 - Karma: 350
Here are downloads for many different paper jigs.

Jul 9 2012 2:38AM
0 0
profile picture
Lemuel
Posts: 14502 - Karma: 10,730
One of the maintenance threads up top has every jib in it. I mounted up some px 15's no problem, drilled first on a piece of wood, everything was perfect, drilled the skis and they are fine. Some of the holes were a tiny bit crooked but nothing detrimental. The skis are on their 3rd mount anyway so not a big deal of something happens. ONLY do it if you are confident in yourself.
Jul 9 2012 7:23AM
0 0
profile picture
Pretzel___Slaya
Posts: 1432 - Karma: 190
What did u use to fill up the older holes when u remounted them
Jul 9 2012 11:20AM
0 0
profile picture
Lemuel
Posts: 14502 - Karma: 10,730
I used golf tees with some wood glue. Put a dab of glue, hammered them in, snapped / sawed them off and hammered them down flush. If they were still poppin up a bit I sanded them down. Works perfectly. Topsheet gets roughed up but doesn't matter.
Jul 9 2012 1:28PM
0 0
profile picture
pmsnow
Posts: 992 - Karma: 87
This is going to come in handy in a few months.
Jul 9 2012 5:20PM
0 0
profile picture
Pretzel___Slaya
Posts: 1432 - Karma: 190
In the video the guy mentions a ski specific drill bit, where could u buy something like that?
Jul 9 2012 6:33PM
0 0
profile picture
rozboon
Posts: 1642 - Karma: 868

Here:

http://bindingfreedom.com/Supplies_c4.htm

Also if you're mounting a lot of bindings you might want to consider getting one of their guide blocks to make sure you drill it straight.

Jul 9 2012 7:56PM
0 0
profile picture
T.MARTIN
Posts: 1333 - Karma: 62
Its honestly not that hard, read the tgr thread on how to do it and refer to the video. The one thing i would recommend is to practice on a 2 by 4 a few times and having a drill with a built in level. (You can also get a crisscross level to attach to a drill that doesn't already have one)
Jul 10 2012 2:19AM
0 0
All times are Eastern (-5)