Member of the Month

KilaTsunami
October, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Griffon forward pressure help

profile picture
NoCoastSkier
Posts: 1038 - Karma: 626
just got new skis and mounted my griffons. but they got crazy prerelease issues(dins at 9). just wondering if anyone can give me a step by step list of kinda a troubleshoot process to tell if the forward pressure is correct?
Nov 20 2011 8:33PM
0 0
profile picture
gnartogue
Posts: 1005 - Karma: 417
step one: go to a shop
Nov 20 2011 8:35PM
0 0
profile picture
NoCoastSkier
Posts: 1038 - Karma: 626
you dont know my shop.... closest scheels is an hour away(sketchy from past experience) closest LEGIT ski shop is 3.5 hours away.
Nov 20 2011 8:41PM
0 0
profile picture
pinguman
Posts: 185 - Karma: 302
just keep going a notch or two forward until it doesnt prerelease.
Nov 20 2011 9:24PM
0 0
profile picture
j.saaaarela
Posts: 1859 - Karma: 856
sounds like the heel piece is too close or far away from your boot. Don't crank your dins up, keep them wherever they were set. There is a screw behind the heelpiece that moves it forward and backward. The heel of the boot should cover the whole tab (the piece you actually stomp on to click in). Anywhere between there and another turn forward is ideal spacing.

A relatively low-impact way to check how well they hold (that is, if you don't go to a shop) is to click in, and lean forward like a big nose butter. if you release, you probably need to adjust the spacing or din, but think of spacing first.

Hopefully that helps
Nov 20 2011 11:01PM
0 0
profile picture
Reed.
Posts: 4489 - Karma: 272
Click your boot into the bindings. Check out the worm screw on the back of the heel piece. If it's flush with the plastic around it, congrats, your forward pressure is correct.

If the screw is sticking out a bit, screw it in accordingly until it is flush.

If the screw is countersunk into the heel piece plastic, back the screw out until it's flush. Really easy to adjust forward pressure on markers.
Nov 20 2011 11:42PM
0 0
profile picture
zack_h123
Posts: 314 - Karma: 109
This. Just to add, make sure you take the boot out of the bindings before you adjust. Then put them back in to check, repeat if necessary.
Nov 21 2011 7:55AM
0 0
profile picture
NoCoastSkier
Posts: 1038 - Karma: 626
THANKYOU + k to all those legit answers
Nov 21 2011 1:57PM
0 0
profile picture
NoCoastSkier
Posts: 1038 - Karma: 626
oh one more thing before i mess around with them. flush with the plastic hole area or flush with the plastic that is a bit raised above it?
Nov 21 2011 2:01PM
0 0
profile picture
Avifarer
Posts: 5926 - Karma: 598
i thought the engraving on the screw is supposed to be flush with the plastic
Nov 21 2011 2:19PM
0 0
profile picture
zack_h123
Posts: 314 - Karma: 109
Flush with the hole that the worm screw sits in.
Nov 21 2011 2:20PM
0 0
profile picture
zack_h123
Posts: 314 - Karma: 109
http://www.gerhardsells.com/OTHER/M12_2.jpg
Nov 21 2011 2:25PM
0 0
profile picture
zack_h123
Posts: 314 - Karma: 109
Sorry couldnt work out how to embed from my IPad
Nov 21 2011 2:28PM
0 0
profile picture
uncski
Posts: 101 - Karma: 39
Click for larger image
Nov 21 2011 3:20PM
0 0
profile picture
NoCoastSkier
Posts: 1038 - Karma: 626
much appreciated everybody!
Nov 21 2011 5:14PM
0 0
All times are Eastern (-5)