Member of the Month

abjectwoe
May, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Removing grips from line poles.

profile picture
LuminatX
Posts: 197 - Karma: 40
Search function on here sucks, cant find anything.
Want to remove the grip from my line pins to cut them down, but can't find any answers.

Thanks.
14 years ago
0 0
profile picture
T.DUDE
Posts: 1681 - Karma: 129
my best guess to do so would be to take a blow dryer and sweep from left to right on the grip to warm the glue underneath.
14 years ago
0 0
profile picture
EricaMN.
Posts: 2704 - Karma: 347
boiling water.
and there are a few threads on this so search around, theres some good answers in a few of em
14 years ago
0 0
profile picture
LuminatX
Posts: 197 - Karma: 40
from what ive found i hear of people putting the grips in boiling water, essentially to do the same thing.
the only thing that made me hesitant was near the bottom of the grips theres little silver holes, thought maybe there was a special key.
14 years ago
0 0
profile picture
array.
Posts: 2439 - Karma: 202
My friend boiled his pin grips and fucked them up. The pins have the baseball grips so you can't boil it. I would use a blowdryer if i were you.
14 years ago
0 0
profile picture
LuminatX
Posts: 197 - Karma: 40
alright, ill give the blowdryer a whirl.
my buddy was stupid and got fed up trying to figure out how to get it off, so he cut it from the bottom lol
14 years ago
0 0
profile picture
AWALLRUS.
Posts: 5762 - Karma: 223
HAY TREVOR.
14 years ago
0 0
profile picture
Panda_with_Guns
Posts: 3040 - Karma: 1,620
lol wtf? how does that work. also use a heat gun. its like a super blow dryer. but assuming you dont have one, take some time and use your moms blowdryer
14 years ago
0 0
profile picture
49566738265
Posts: 0 - Karma: 7,705
Boiling water is superfluous. I take grips off with the hot water in the bathroom sink. You don't have to waste time and destroy stuff with boiling water.
14 years ago
0 0
profile picture
SKIU4EA
Posts: 2388 - Karma: 2,086
The space/crack in an open door where the hinges are, is just enough space for a ski pole to slide down into from the top. The space is too narrow for the grip to pass through, so it's like a nice make-shift vice to pull your grips off if you don't have a vice.


note** don't impale yourself
14 years ago
0 0
profile picture
X-REY
Posts: 996 - Karma: 387
if they're just rubber, and you have an air compressor, you can just put the hose in the grip and it should just slide right off. you could also use a bike pump. it works on bike grips, i feel like it's the same principle for ski poles.
14 years ago
0 0
profile picture
c4t_l0ver
Posts: 5485 - Karma: 810
my brother has the pin's and he just used hot water. they came right off. .
14 years ago
0 0
profile picture
KillaSteeze
Posts: 3329 - Karma: 351
Just hot water sounds like it would work, don't know why your buddy would even consider cutting them
14 years ago
0 0
profile picture
NinetyFour
Posts: 8650 - Karma: 13,410
Hot water works realllll well. I remove my grips and basket seats with just hot tap water over the weekend to paint my k2 revolver poles (Original finish was shit) It will take a few rounds of letting the grips soak in hot water, then reefing on them, then back into the water to get them off, but be patient. Putting a dry cloth over the grips or basket seats helps too.
14 years ago
0 0
profile picture
NinetyFour
Posts: 8650 - Karma: 13,410
Hot water works realllll well. I remove my grips and basket seats with just hot tap water over the weekend to paint my k2 revolver poles (Original finish was shit) It will take a few rounds of letting the grips soak in hot water, then reefing on them, then back into the water to get them off, but be patient. Putting a dry cloth over the grips or basket seats helps too.
14 years ago
0 0
All times are Eastern (-4); Currently it's 1:18AM