Member of the Month

partyandBS
December, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Tips on pvc rail

profile picture
crab_pretzel
Posts: 3919 - Karma: 622
Ive seen abunch of threads about cheap and easy rails and its obvious pvc is the cheapest. i just dont really know how to anchor the pvc to a base.  I already have a sturdy base made out of wood that with an older countertop secured with screws i counter-sinked with a drill bit. this didn't work out because it was just wood with a hard laminate but it makes for a great base for something. i just need to learn how to secure pvc to the top of it. thanks for any helpful answers on this
Jan 11 2011 9:11PM
0 0
profile picture
mowdapow
Posts: 223 - Karma: 48
Well first off, get some PVC. Now put it on the snow. Your done.
Jan 11 2011 9:15PM
0 0
profile picture
crab_pretzel
Posts: 3919 - Karma: 622
it can slide out when you hit it. and i kinda want something a little more permanent
Jan 11 2011 9:18PM
0 0
profile picture
Lwaghorn
Posts: 143 - Karma: 14
drill hole through top of pvc. put screw throught the hole. screw through pvc onto wood. this what you where looking for?
Jan 11 2011 9:21PM
0 0
profile picture
Emma_Watson
Posts: 4491 - Karma: 6,799
you sir, are a dumbass.
build a jib 101 cult gogo!
Jan 11 2011 9:21PM
0 0
profile picture
crab_pretzel
Posts: 3919 - Karma: 622
i dont know if youve tried this, but could you ever catch an edge on the drill holes in the top? and this doesn't seem very laterally stiff
Jan 11 2011 9:23PM
0 0
profile picture
mowdapow
Posts: 223 - Karma: 48
Well this is my set-up, never slides, just pack some snow around the sides, it will freeze in place. Maybe try putting a small brick or something at the bottom, so it won't move forward if your having problems. You could build a platform, but this ways it's more portable, and it's low so you just need enough snow for a small run in. Plus learning tricks is easier.
Jan 11 2011 9:24PM
0 0
profile picture
McFellon
Posts: 1841 - Karma: 2,005
no, this actually works. plus, it's the easiest, and to my knowledge, only way of putting pvc on the base
Jan 11 2011 9:26PM
0 0
profile picture
theWIZARD
Posts: 935 - Karma: 76
i did the same technique for mine and it works fine. drill a hole every 8 inches or so.
and no you don't catch an edge. when you're done drilling, sand down the top holes (just a little)
Jan 11 2011 9:27PM
0 0
profile picture
[evan]
Posts: 5628 - Karma: 117
I could PM you some pics in the morning of how I built mine if you want

Jan 11 2011 9:28PM
0 0
profile picture
crab_pretzel
Posts: 3919 - Karma: 622
how wide should the pipe be? im new to pvc setups so any help is much appreciated

Jan 11 2011 9:28PM
0 0
profile picture
crab_pretzel
Posts: 3919 - Karma: 622
yea if you had the time that would actually be a big help. these tips are really helpful
Jan 11 2011 9:31PM
0 0
profile picture
crab_pretzel
Posts: 3919 - Karma: 622
if i drilled through the bottom with screws is there a chance the pvc could split or crack at all?
Jan 11 2011 9:49PM
0 0
profile picture
Backyard.Skier
Posts: 5397 - Karma: 1,498
build a jib 101 has hundreds of building answers and suggestions
Jan 11 2011 9:52PM
0 0
profile picture
j.saaaarela
Posts: 1859 - Karma: 856
http://www.youtube.com/watch?v=8lrx9S2sMVs

starts at 1:09. No holes in the top, super secure, and relatively simple.
Jan 11 2011 10:32PM
0 0
profile picture
trettzilla
Posts: 931 - Karma: 29
you can buy square pvc pipes. i just lay mine in the snow
Jan 11 2011 10:43PM
0 0
profile picture
crab_pretzel
Posts: 3919 - Karma: 622
thanks i like this idea the best
Jan 12 2011 4:10PM
0 0
profile picture
monkatizer
Posts: 4704 - Karma: 1,518

its simple, either drill a couple holes in the top, (1 hole every 3 feet is good) then using some good screws put them thru the hole then drill them thru the pvc then into the wood,   make the hole in the top only, and make it bigenough thetathe bit and screw head can fit in it.   and the holes dont catch your skis i gaurentee it, its never happened to me, i used this meathod

or you can go up from the bottom by pre drilling holes thru the wood only then take a screw longenough to go thru the wood and the pvc but not so long that it goes out the top of the pvc, this also works well, make sure not to strip the pvc by screwing the screw too much, after its secured the pvc,   i have used this meathod too, but i only recomend using this when u hav 2 or more pipes, unless you use huge screws with huge and course threads

good luck 

Jan 12 2011 6:50PM
0 0
profile picture
Ski_ThEast
Posts: 1676 - Karma: 272
i use a 2'' by 6'' then 1 1/2'' pvc and cut them down the middle so then you only need one the drill holes through the pvc then screw it in so far it has worked great for me

Jan 12 2011 6:59PM
0 0
profile picture
theabortionator
Posts: 52027 - Karma: 167,123
Buying pvc can land you on the terrorist watch list. Be sure to buy less than 3 pipes and no longer than 10 feet each.
Jan 12 2011 7:06PM
0 0
profile picture
monkatizer
Posts: 4704 - Karma: 1,518
at roughly 3 dollars for a 10 foot section of 1 1/2 pvc cutting it down the middle sounds like a hassle, just by another pipe, nbd  i would do that if it was 10 or more bucks tho
Jan 12 2011 7:09PM
0 0
profile picture
belden...
Posts: 2914 - Karma: 1,274
How big is your pvc?
Jan 12 2011 7:18PM
0 0
profile picture
123+ski
Posts: 2832 - Karma: 581
i did this to attach it to a 2x4 cuz i have a single barrel and it worked fine
Jan 12 2011 7:27PM
0 0
profile picture
Stickity
Posts: 7750 - Karma: 769


unbelievably sturdy
has lasted me 4 years of skating and now 2 years of skiing
Jan 12 2011 7:29PM
0 0
profile picture
Heart
Posts: 6156 - Karma: 3,464
i did mine like this, works great:

https://www.newschoolers.com/ns3/web/popups/viewimage.php?media=http://i298.photobucket.com/albums/mm253/dudesirule2/untitled1.jpg
Jan 12 2011 7:45PM
0 0
profile picture
gGrove
Posts: 193 - Karma: 143
drill diagonally into the pvc to the wood
Jan 12 2011 11:23PM
0 0
profile picture
Andi_G
Posts: 3086 - Karma: 15,117
Shit.
Jan 12 2011 11:51PM
0 0
profile picture
Grilledsteeze212
Posts: 211 - Karma: 137
this is how i built my rail
http://www.youtube.com/watch?v=uf3XPQCuyDc
Jan 12 2011 11:55PM
0 0
profile picture
DADDYlongLEGS
Posts: 1574 - Karma: 48
up through the bottom
Jan 12 2011 11:56PM
0 0
profile picture
SteezyMan97
Posts: 7 - Karma: 10
I am building a pvc rail right now and i used this vid but i am only using 2 pipes instead of 4. this is sturdy and easy to build if you use this vid
Jan 13 2011 12:17AM
0 0
profile picture
Tahoe_Steve
Posts: 443 - Karma: 11
Try liquid cement (any hardware store. I went to Ace). Make sure to read all the labels to see which one goes the best with wood/pvc material bonding; as I forget which one it is...
Not too expensive, so use a lot and let it dry...don't use it the day you make it. I'm not 100% positive this is super strong, but I've never had a problem with it!!
Jan 13 2011 1:16AM
0 0
profile picture
crab_pretzel
Posts: 3919 - Karma: 622
any recomendation on type/ size of pvc? i was thinking of using something like 4inches in diameter for a rail thats just one pipe wide
Jan 13 2011 3:55PM
0 0
profile picture
Gramtorp
Posts: 9 - Karma: 24
http://vimeo.com/18614154

I just kinda try to surround two (or one) big pwc pipe with lots of snow.. and it work even though its going downhill.
Jan 13 2011 5:50PM
0 0
profile picture
Mr.DarthVader
Posts: 1322 - Karma: 556
thats what i do
Jan 13 2011 6:12PM
0 0
profile picture
Stickity
Posts: 7750 - Karma: 769
lol it just broke tonight
but still 4 years out of 1 pvc pipe?


and if you catch on holes, stop skiing immediately because you are doing something unbelievably wrong
i skied mine with a crack splitting it into two 5' pieces and it still worked
Jan 13 2011 8:08PM
0 0
profile picture
Ski_Alot
Posts: 5908 - Karma: 3,728
i duck taped the pipes to the board the drilled a pretty small hole through the board and pipe and put in a big bolt in three places
Jan 13 2011 8:14PM
0 0
profile picture
crab_pretzel
Posts: 3919 - Karma: 622
duct tape? i dont really see how this works
Jan 16 2011 2:32PM
0 0
profile picture
cooper.fry
Posts: 2229 - Karma: 34
Build-A-Jib cult has what you need my friend.
Jan 16 2011 2:40PM
0 0
All times are Eastern (-5)