Member of the Month

hi_vis360
November, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Can i just unscrew my ski bindings?

profile picture
kryptic
Posts: 111 - Karma: 10

Would it be bad ii just unscrewed my ski bidnings, i plan to re-attach them a couple minutes later i just want to put the heel piece of my old binding over that same spot to check something.

Is it as simple as screwing and unscrewing?

Feb 23 2010 8:56PM
0 0
profile picture
BWalmer
Posts: 9141 - Karma: 12,885
yes, use a #3 hand screwdriver (you can use a power drill, but if you're new to mounting/unmounting it's a bad idea). Before you remount them simple put some wood glue in the holes (just a tiny bit) to help waterproof it.
Feb 23 2010 9:00PM
0 0
profile picture
mvele
Posts: 101 - Karma: 12
Pretty much, you need some glue in the holes before you put your binding back on for good.
Feb 23 2010 9:00PM
0 0
profile picture
kryptic
Posts: 111 - Karma: 10
Sorry i had a typo, i ment put the heal piece of my new binding in the spot. m probably getting them re-mounted tomorrow a just want to see if the brakes fit well or not. If i dont get them mounted id be using the old bindings for 1 more time (thursday) then do away with them so is the glue still necessary?
Feb 23 2010 9:04PM
0 0
profile picture
kryptic
Posts: 111 - Karma: 10

also whats a #3 screwdriver?

A normal philips head wont work?

Feb 23 2010 9:10PM
0 0
profile picture
kabozo101
Posts: 4429 - Karma: 20
a number 3 is a phillipshead, just a bit bigger than the normal one
Feb 23 2010 9:26PM
0 0
profile picture
BWalmer
Posts: 9141 - Karma: 12,885
yes, cause the glue is what keeps it watertight, without it water can get into the holes and cause the core to rot causing a pull-out.

A #3 screwdriver is a Phillips Head Screwdriver, it's just a size. A "normal" phillips head is usually a size 2, you usually need something bigger or you risk striping the screw head making it next to impossible to take the binding off. It looks like a regular phillips head, but the tip is flatter and wider.
Feb 23 2010 9:27PM
0 0
profile picture
PhuzzyWuzzy
Posts: 358 - Karma: 82
Ski binding screws are not Philips Heads. 

You are supposed to use a #3 Pozidriv screwdriver with these screws to prevent stripping them, however a #3 Philips will usually work, just be careful. 
Feb 24 2010 12:20AM
0 0
profile picture
20Valv3
Posts: 117 - Karma: 11
I was about to say this...
Feb 24 2010 12:25AM
0 0
profile picture
BWalmer
Posts: 9141 - Karma: 12,885
yeah, but I figured he didn't happen to have one lying around, it's hard enough to have a #3 lying around.
Feb 24 2010 12:27AM
0 0
profile picture
madsskaar
Posts: 492 - Karma: 191
yes.
Feb 24 2010 7:12AM
0 0
profile picture
iffe
Posts: 984 - Karma: 120
You don't have to take off your current binding to do that. Turn your ski upside down and put the other binding on top of the ski's base to see if the brake fits. Or you could just measure the brake and then measure your ski.
Feb 24 2010 7:32AM
0 0
All times are Eastern (-5)