Member of the Month

KilaTsunami
October, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Input on update please

profile picture
Whifazoo
Posts: 737 - Karma: 132

okay so my setup was pre sketchy but worked well, so for fall and the last bit of summer i was looking to update it so i made these on autodesk 3ds max, tell me what u think i should change(btw the white stuff is box top sheet strips that i found chiilin at pano

Click for larger imageClick for larger imageClick for larger imageClick for larger image

Aug 19 2009 7:23PM
0 0
profile picture
*Nickdel*
Posts: 2264 - Karma: 956
wow thats a pretty dope setup. IMO i dont think you need to change anything on it!!
Aug 19 2009 7:27PM
0 0
profile picture
Whifazoo
Posts: 737 - Karma: 132

lol i meant thats what i wanna do for the update, hahaha sorry.

i was jw if u thought i could inprove on any areas before i built onto my setup now, (pre much the only thing im going to use from my setup now is the tower and re-do all of the run in and shit )

Aug 19 2009 7:32PM
0 0
profile picture
ashamedkrew
Posts: 1194 - Karma: 424
its one thing to actually build the setup, but then re-built it on the computer.  Mucho effort
Aug 19 2009 7:34PM
0 0
profile picture
stormtrooper
Posts: 1191 - Karma: 461
that looks like its going to be pretty legit post pics when its done.
Aug 19 2009 7:53PM
0 0
profile picture
Whifazoo
Posts: 737 - Karma: 132
will do man
Aug 19 2009 9:21PM
0 0
profile picture
Mr.Huck
Posts: 6096 - Karma: 14,896
Autocad drawings of summer setups, backyard jibbing is getting way sophisticated.  Nice!!!
Aug 19 2009 9:40PM
0 0
profile picture
Chickendodo
Posts: 1426 - Karma: 33
I dunno but it looks a little weak right at the bottom of the ramp part.  Just my two cents, but you might want to fortify that part.
Aug 19 2009 9:41PM
0 0
profile picture
Zoro
Posts: 1253 - Karma: 37
haha thats all i did last year in drafting. just draw 3d rails and shit
Aug 19 2009 9:47PM
0 0
profile picture
Whifazoo
Posts: 737 - Karma: 132

sick thaks man

Aug 19 2009 10:01PM
0 0
profile picture
@skiinmitch
Posts: 2781 - Karma: 78
where are the pics lol. i wanna see all the work u have done while i was sitting and watching u work lol
Aug 25 2009 1:29AM
0 0
profile picture
Whifazoo
Posts: 737 - Karma: 132
lol i will post them when its al finished , that will be later tomorrow
Aug 27 2009 12:24AM
0 0
profile picture
Steeze-On-Toast
Posts: 679 - Karma: 92
wow those designs look pretty slick. how slippy are those steel plates going to be? maybe grease them up abit(Y)
Aug 27 2009 1:41PM
0 0
profile picture
panojibber
Posts: 3382 - Karma: 216
Not steel plates, but box top sheet. : )

First attempt was a failure, due to uber compression coming into the spot before the lip where its flat. However, whifazoo has plans to make it work.
Aug 27 2009 6:51PM
0 0
profile picture
KJL.
Posts: 307 - Karma: 11
im no engineer but it looks liek you might want to throw some vertical supports in the tranny/ramp, everything is on an angle. but a very nice looking setup
Aug 28 2009 4:26AM
0 0
profile picture
@skiinmitch
Posts: 2781 - Karma: 78
lol. u just missed it it was a EPIC fail. super compression. it will get done...... sometime in thde near future
Aug 30 2009 2:53AM
0 0
profile picture
Whifazoo
Posts: 737 - Karma: 132

im going to finish it tomorrow mornight

Aug 30 2009 3:27AM
0 0
profile picture
lydiaiskwllol
Posts: 514 - Karma: 11
Looks pretty good to me
Aug 30 2009 6:56AM
0 0
All times are Eastern (-5)