Member of the Month

theabortionator
April, 2025

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

How to put skiers on your helmet the right way

profile picture
C-Burg
Posts: 4729 - Karma: 130
Every time I try to put stickers on my helmet, it suck and the stickers have a bunch of bubbles and shit. How do you do it the right way?
16 years ago
0 0
profile picture
C-Burg
Posts: 4729 - Karma: 130
SHIT... i ment to say How to put stickers on your helmet the right way
16 years ago
0 0
profile picture
OAK_TREE
Posts: 2683 - Karma: 12
try putting them on one side first then smoothing out the rest of the sticker until it is fully on and smooth. also try finding the flattest spots of your helmet. those areas normally work best.
16 years ago
0 0
profile picture
VTtreeskier
Posts: 1833 - Karma: 64
If your putting on diecuts it can help to cut small slits in the paper stuck to the stickers, makes it easier to contour the sticker to the curve of your helmet
16 years ago
0 0
profile picture
no_steeze_in_NY
Posts: 225 - Karma: 13
i find if i really cant smooth it down, if you  carefully and minorly cut the sticker where its bubbling you can get them flat, and if your careful overlapping them no one can tell the difference
16 years ago
0 0
profile picture
skodeo7
Posts: 14950 - Karma: 9,263
Start from one corner/side. Slowly with your thumb press the rest of the sticker down (make sure your holding the other side of the sticker with your other hand so it doesn't accidently get stuck). Make sure your doing this in a warm room. Applying stickers in the cold is counterproductive. You can warm up the surface and still do it though.
16 years ago
0 0
profile picture
no_steeze_in_NY
Posts: 225 - Karma: 13
i find if i really cant smooth it down, if you  carefully and minorly cut the sticker where its bubbling you can get them flat, and if your careful overlapping them no one can tell the difference
16 years ago
0 0
profile picture
WeK
Posts: 1894 - Karma: 11
go from one corner/side and slowly press down as others have mentioned. if a place is bubbling up , push to form like a thin ridge that goes up, try to get it at a spot which doesnt affect the sticker, then get a lighter and run it over quickly a few times it'll flatten the ridge right out. i pretty much but a lighter to all of my stickers, seems like it makes them hold better, and if you have any that come out over the edge of the helmet a bit it'll take it right off
16 years ago
0 0
profile picture
Bepo
Posts: 8195 - Karma: 17
i mounted a pair of bindings on my helmet to solve this very problem
16 years ago
0 0
profile picture
luke8
Posts: 130 - Karma: 54
if their from vinyl go with a go over the sticker with a lighter...
16 years ago
0 0
profile picture
JoshBishop
Posts: 464 - Karma: 748
A blow dryer works really well too. Any sticker that I apply with a blow dryer is less prone to flaking, chipping, and bubbling and stays on much longer.
16 years ago
0 0
profile picture
narwhal
Posts: 509 - Karma: 281
Use a lighter on the bubbles and melt them flat.
16 years ago
0 0
profile picture
patrickstar
Posts: 486 - Karma: 20
use your tongue to push them down
16 years ago
0 0
profile picture
ace_
Posts: 3189 - Karma: 38
This might work, i use it when i put on mx decals.

just make a batch of light soap water and then put some soap water on the spot where you want the sticker and you can slide it around until you have it where you want it. then squeegee until it sticks.
16 years ago
0 0
profile picture
popNfresh44
Posts: 3757 - Karma: 44
cut little slits along the edges if its a normal sticker, then the slits can overlap or expand to accommodate for the curvature of your lid. if its a decal (2 peels), just apply it like everyone else said, it doesnt matter if theres bubbles in the semi-transparent paper, just make sure there arent any bubbles in the actual decal itself.
16 years ago
0 0
profile picture
mizzike
Posts: 1386 - Karma: 251
hahaha
16 years ago
0 0
profile picture
ASkierNamedJaymz
Posts: 1209 - Karma: 341
yep. hold the back of the sticker with your other hand
16 years ago
0 0
profile picture
GGreene
Posts: 993 - Karma: 42
(for die-cuts) i usually put them on then heat them up using a lighter then take the piece of glossy paper (not the thin one that is sticky) and then rub the slick side along the sticker to make sure it sticks nice 'n good
16 years ago
0 0
profile picture
huge-go
Posts: 1451 - Karma: 33
hahaha
+k
16 years ago
0 0
profile picture
pbcrazy9898
Posts: 274 - Karma: 21
stickers are meant to be put on flat surfaces... when you put them on something spherical they stretch and bunch up... cut little slits where they bunch and stretch to help.
16 years ago
0 0
profile picture
Malcolm
Posts: 15953 - Karma: 9,501
hahaha well said sir
16 years ago
0 0
profile picture
birdshake
Posts: 1228 - Karma: 71
for die cuts I kind of stick the center down first and work my way out and ive never had a problem with wrinkles or bubbles this way though I do take my time.
16 years ago
0 0
profile picture
skifree179
Posts: 769 - Karma: 17

Start from the very side of the sticker and use your thumb or a credit card and smooth it down  to eliminate bubbles)

If u have bubbles use an exacto knife and poke the bubble and work the air out

16 years ago
0 0
All times are Eastern (-4); Currently it's 1:49PM