Member of the Month

KilaTsunami
October, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

Cutting poles

profile picture
tomtheelf
Posts: 65 - Karma: 14

can you cut a composite pole? or will it splinter? if you can what would you cut it with?

Nov 11 2008 11:23AM
0 0
profile picture
Tex.
Posts: 1106 - Karma: 124
if you mean carbon fiber poles then yes you can cut them. all you need is a pole cutter, they look like this if you dont know what they are, you can buy them at home depot for 10-15 bucks.

http://www.polesandtracks.co.uk/acatalog/CurtainPoleCutter.jpg
Nov 11 2008 11:29AM
0 0
profile picture
tomtheelf
Posts: 65 - Karma: 14
thanks man. is that pretty much the same deal as a PVC pipe cutter?
Nov 11 2008 11:31AM
0 0
profile picture
TimmyK
Posts: 779 - Karma: 15
hacksaws work best, tape tightly with masking tape where your gonna cut and use a fine tooth blade 32tpi or better... some companies even make special blades for cutting carbon fiber.  some guys also you cutting wheels.  when done sand down the end for a clean finish.
Nov 11 2008 1:28PM
0 0
profile picture
Tucks
Posts: 2120 - Karma: 161
you will want to wear gloves otherwise you will probably get some nasty splinters, and they hurt like a bitch
Nov 11 2008 2:32PM
0 0
profile picture
AEROPLAEHN
Posts: 1353 - Karma: 192
yeah, hacksaw forsure.
Nov 12 2008 11:27AM
0 0
profile picture
Shredneck
Posts: 2051 - Karma: -32
If your talking about the bendy poles they arnt carbon fiber there fiberglass carbon fiber is rigid
Nov 12 2008 11:38AM
0 0
profile picture
seeingstars
Posts: 422 - Karma: 14
no, carbon fiber flexes as well.

Nov 12 2008 11:43AM
0 0
profile picture
seeingstars
Posts: 422 - Karma: 14
exactly
just tape as tight as possible before you do it

Nov 12 2008 11:43AM
0 0
profile picture
Alex_G
Posts: 11902 - Karma: 1,019
i used a circular saw when i cut my goode composite poles and that worked perfectly but they snapped the other day i dont think it had anything to do with cutting them because they snapped right down the middle.
Nov 12 2008 11:46AM
0 0
profile picture
AEROPLAEHN
Posts: 1353 - Karma: 192
last season i broke 2 pairs of aluminum poles an then snagged a pair of carbon composite poles and i haven't had a break yet. :)
Nov 12 2008 12:00PM
0 0
profile picture
Steazel
Posts: 553 - Karma: 16
tried to cut composites the other day and they snapped :(
Nov 12 2008 12:04PM
0 0
profile picture
wiglaf
Posts: 4877 - Karma: 141
I would make sure you have the pole in a vice right up to where you want to cut make the cut. Seems like vibrations from cutting is what can cause these types of poles to split.
Nov 12 2008 12:51PM
0 0
profile picture
seeingstars
Posts: 422 - Karma: 14
i think you can also do it with a jigsaw


Nov 12 2008 1:31PM
0 0
profile picture
borskee
Posts: 796 - Karma: 127

i have a question too

i have K2 Silencer poles from a few years ago

its there an easy way to remove the foam grip and put it back on?

Nov 12 2008 5:04PM
0 0
profile picture
wiglaf
Posts: 4877 - Karma: 141
sticking your grips in boiling water for a min or so can loosen them up. Also use a thin screw driver to work the grips off
Nov 12 2008 6:15PM
0 0
All times are Eastern (-5)