Member of the Month

KilaTsunami
October, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

HDPE problems?

profile picture
skiWASHDC
Posts: 716 - Karma: 17
I got 1/4 inch and applying it with a countersink bit was easy as easy comes.

HDPE is awesome and slippery. BUT
I noticed its quite soft?
I toook my sharpest edges and they dug in pretty easy but i was thinking with my mellow edges with an even higher impact wont they dig into the surface or scratch?

Anyone had any problems with it or any solutions to your problem?
Nov 30 2006 8:31PM
0 0
profile picture
SkiMN
Posts: 4005 - Karma: 38
Sounds weird as hell. I doubt it would have got its reputation as one of the best materials for box topsheets if it caught though.
Nov 30 2006 9:29PM
0 0
profile picture
HeathR
Posts: 4359 - Karma: 1,382
it had lasted 3 seasons and still holding up good. I dont use sharp skis though.
Nov 30 2006 10:22PM
0 0
profile picture
dubage
Posts: 1122 - Karma: 639
if you have coaping, nothing to wory about
Dec 5 2006 10:06PM
0 0
profile picture
turtleman321
Posts: 192 - Karma: 7
really no point in having HDPE if you have coping. but anyway, is it just the edges? mine did it to but once the edges dull out it works good. if its catching in the middle sounds like your skis arent landing flat or there is some kind of high spot on the sheet of HDPE
Dec 5 2006 10:32PM
0 0
profile picture
ccdickson
Posts: 33 - Karma: 10
yah i just built a box with HDPE as a topsheet, and ill admit it does fray a little on the edges. but im pretty sure its near impossible to catch in the middle of the sheet. also mines not all that slippery, should i just like wax it down or something?
Dec 5 2006 10:33PM
0 0
profile picture
skiWASHDC
Posts: 716 - Karma: 17
snow
Dec 6 2006 7:12AM
0 0
profile picture
socktrooper
Posts: 337 - Karma: 13
where you get the HDPE plastic?
Dec 6 2006 3:46PM
0 0
profile picture
teamjib
Posts: 217 - Karma: 10
^any plastics manufacturer just look on the internet or phone book thers lots. i just got some today
Dec 6 2006 6:13PM
0 0
profile picture
skiWASHDC
Posts: 716 - Karma: 17
www.usplastics.com
Dec 6 2006 7:03PM
0 0
profile picture
+[wall.e]+
Posts: 1928 - Karma: 18
Fuck dude, I just payed 42 for a 4x8 foot sheet the other day, then got screwed on the shipping. $48 for shipping, plus it has to be cut in half into two 4x4s. So my 16ft box will be comprised of four 4ft sections. Damn. $100.... Whats the cheapest place to buy it?
Dec 6 2006 7:44PM
0 0
profile picture
skiWASHDC
Posts: 716 - Karma: 17
100$ for a 16 foot box aint that bad i dont think
Dec 6 2006 9:39PM
0 0
profile picture
garrett.
Posts: 9304 - Karma: 3,670
think 1/8 inch is thick enough?my box's are going to be 1x10
Dec 7 2006 6:59PM
0 0
profile picture
HeathR
Posts: 4359 - Karma: 1,382
It depends on how you plan on attaching it. If ur gonna screw it on u need to countersink ur screws so you dont ketch ur edge on them. You cant countersink in 1/8 inch its too thin.
Dec 7 2006 7:44PM
0 0
profile picture
seider
Posts: 958 - Karma: 23
i was told u can get special glue attaching HDPE to wood, im making my box 1.5*12
Dec 11 2006 10:34PM
0 0
All times are Eastern (-5)