Member of the Month

KilaTsunami
October, 2024

Online

Welcome to the Newschoolers forums! You may read the forums as a guest, however you must be a registered member to post. Register to become a member today!

any ski techs, help

profile picture
skir216
Posts: 741 - Karma: 10
aight im gona sound like a complete moran, but i was mounting my concepts the other day and striped two holes in the rear of the binding (pivot 10) (someone fucked with the torch on the screw gun and it just kept tuning the screw)asides from heli coiling them i was thinking of epoxing the holes and then just redrilling them or maybe just mountin the skis center cause i was thinking of doing that anyway, any ideas guys?
*JaSoN*
Feb 7 2003 2:18PM
0 0
profile picture
Summit_punk
Posts: 381 - Karma: 10
if you want to move them forward anyway then just move them a cm up from where they are now...when you drill the new holes make sure to use waterproof wood glue. it bonds best because of the wood in your ski. don't use apoxy cause it can just pop out cause it doesn't bond as well as wood glue.
Feb 7 2003 2:34PM
0 0
profile picture
EmcEEmahEm
Posts: 466 - Karma: 10
I highly enjoy mounting skis with a jig. It makes things so much easier and you never overdrill or put a hole in the wrong spot. That said, I have done it on the fly too. Center-mounting a ski that is not a true twin WILL decrease its performance, the sidecut (s) are centered at the mounting point.


Eric Peterson
Freeski Specialist
Tyrol Ski and Sports
Rochester, MN
Feb 7 2003 4:17PM
0 0
profile picture
jizack
Posts: 2486 - Karma: 16
why would you even try to mount bindings without a jig? not really the smartest thing in the world, and for stripping out the holes you shoudl just use like a 3pt posi drive to tighten the screws down and you really don't need to worry about stripping them out, also remember to tap the holes also. and just in case you didn't know there is specific drill bits you use to mount bindings for certain skis. for a concept i believe its a 3.5x9



fuk that
Feb 7 2003 4:23PM
0 0
profile picture
skir216
Posts: 741 - Karma: 10
nah of course i mounted them with the jig that wasnt the issue, when i was puttin the screws in someone at my shop fucked the torch on the gun and so they just kept on spining and stiped the holes,
*JaSoN*
Feb 7 2003 4:46PM
0 0
profile picture
UpDawg
Posts: 2373 - Karma: 11
yeah thats right, 3.5x9 is what you use for almost all skis, with some exceptions- but if you didnt want to move the bindings forward at all, keep your toepiece where it's at, then drill new holes for the heel either forward or back of the original holes (plug them up first), and keep the new holes somewhat close to the old ones (not too close though). once you mount the heel piece again, just adjust the piece back or forward, depending on whether or not you drilled in front or back, and you'll be good. if not, then just take both pieces out, plug the holes, and remount like a cm forward- good luck
Feb 7 2003 5:49PM
0 0
profile picture
skir216
Posts: 741 - Karma: 10
yes, but then the forward pressure would be off
*JaSoN*
Feb 7 2003 6:02PM
0 0
profile picture
Lateralis
Posts: 1228 - Karma: 332
ive mounted bindings without a jib,theyve never came out once,so i must be doing something right
Feb 7 2003 6:28PM
0 0
profile picture
UpDawg
Posts: 2373 - Karma: 11
no dude, the forward pressure will still be fine- think of rental bindings, the heel on that gets adjusted so many times, it doesnt matter where it gets adjusted to, what matters is whether or not the heel is coming in contact with the heel of the boot- so the forward pressure would still be alright. dont worry about it, you'll be fine. i've done this with a pair of skis before, and it works out really good.
Feb 7 2003 8:25PM
0 0
profile picture
jizack
Posts: 2486 - Karma: 16
yea you can safely move your heelpiece forward or back a bit without worrying about forward pressure or any of that crap, cause even if you were to say remount with a different boot with a slightly smaller or larger boot sole length the toe piece doesnt even move ususally, and besides the heel piece is adjustable.



fuk that
Feb 8 2003 12:19AM
0 0
profile picture
schlonginator
Posts: 3971 - Karma: 27
arn't you supposed to get a qualified professional to mount your skis with a jig???


________________________

Just JIB It !!
Feb 8 2003 3:37AM
0 0
profile picture
Billups
Posts: 3960 - Karma: 329
you don't have to, if you know what you are doing, then go for it...but the tech can do it a bit better maybe...i dunno...




'If you ever catch on fire, try to avoid looking in a mirror, because I bet that will really throw you into a panic'
Feb 8 2003 12:04PM
0 0
profile picture
UpDawg
Posts: 2373 - Karma: 11
mounting bindings without a jig is just plain stupid...its difficult to do, and there is way too much room for error. just use a jig.
Feb 8 2003 11:04PM
0 0
All times are Eastern (-5)